Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
nodic example in \connect SDK\v1.5.0\nrf\samples\bluetooth\peripheral_lbs , ,i can not find the software interface place in peripheral_lbs example code from where to send
Hi.
I'm trying to make the i2cDevlib work on an nRF52 DK board.
There are several ports of the same to nRF51, and one to nRF25 but on the old SDK11.
I'm using SDK15...
Hello,
The Zephyr OS provides a function to reboot the module, sys_reboot(type) where type is either a cold or a warm reboot.
However I cannot find anywhere the difference...
Hello,
We opened from a clean download the example " ble_app_uart " in this folder:
\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs...
Hi, Community!
My development environment is the following:
SDK52,
nRF52840,
s140 17.2.0
nRF Sniffer
My problem is that I can not seem to be able to send more...
Hello,
We are working with the nRF52840 and the OTA works when I set 0x10001304 to a value from 0-3. When I set 0x10001304 to a value of 4 or 5, the OTA fails.
Hi there,
I'm developing with the nRF52840 right now.
I'm trying to read some sensordata with TWI. The sensors are BMM150, BMI270 and BMP388.
Unfortunately, I already...
Hi everybody,
I received a nRF52833 DK (PCA10100) and I was capable to install heart rate example dropping prebuilt hex into the mass storage driver. Later I flashed a led...
Hi
I have seen some queries for support asking if app_timer can be used for real time clock and calendar functionality,
i am using the nRF52810 but the answers were either...
Hi,
I'm very new to learn nrf52832. Recently, want to connect my NRF52832 device with pc, then , using the value uploaded from the device to draw a curve in pc' client....
Hello
I'm looking for API example to use Key Management Unit (key storage and key usage). But I didn't find it in all nordic documentation.
Could you help me to use KMU...
I am using the SDK 17.0.2 to make the advertisement and scanning for the two nrf52840 boards. One unit with extended advertisement only on channel 37 and the other unit scan...
The documentation says that: " By default, threads run in supervisor mode and allow access to privileged CPU instructions, the entire memory address space, and peripherals...
Dear Community;
I am trying to send some data via Lora with a nRF9160 connected with SPI to RF95W Lora module. The transmitter is a nRF9160 with a RF95W, and the receiver...
