Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
I am using the IQ values collected from the Channel Sounding example. The data in the 0 section seems to indicate that this channel is not in use? For example, as shown in...
Hi, I see this goes back at least as far as v2.4.4 and still exists in v3.1.1. Around line
if ((!err) && (err != -EALREADY)) { LOG_ERR("Stop LE scan failed (err %d)", err...
nRF52840 datasheets says it supports 3 SPI slaves, but I need 4 SPI slave devices on my next design (the current design uses 2 SPIs). I don't need DMA transfer at this moment...
I am trying to implement Attribute caching as described in Vol 3, part G, section 2.5.2 of the Bluetooth Core Spec .
Reading the GATT Database Hash seems to work:
The...
Hi Nordic team,
I’m working with an nRF9160-based device and have observed inconsistent LTE behavior when the device operates in areas with poor or unstable signal strength...
Hi,
I want to synchronously get data from different nodes.
Can BLE mesh obtain information from multiple nodes simultaneously? I would like the collected data to have...
Hello,
Using nRF Connect vscode extension, vscode is very slow and almost unusable.
The following process is started multiple time and i have an instance taking 100...
I have an issue with the Lightness setup server set cb being triggered without a connected device and is not internally called in my code. Yet for some reason the set cb is...
Hi
I noticed nordic provides Wi-Fi: Throughput to evaluate the throughput when device is working in STA mode.
If I want to evaluate the device in AP mode, is there any...
Hallo, we are evaluating the UART peripheral of the nrf54l15. As a first step, we are trying to get two DK to communicate with each other, unfortunately without success. ...
Hi all,
I'm looking at an issue and I can't get my head around it. I clearly do something wrong here but I'm stuck.
On our nRF54L15 DK we have a program that can show...
Dear Teams,
I’m using an nRF9151DK board running a simple firmware (example link: github.com/.../ subsys /pm/ device_pm ).
I connected a Power Profiler Kit II (PPK2) to...
Hi,
When I was developing, I found that the matter sample is a little different from the Bluetooth sample .
I want to disable CONFIG_THREAD_LOCAL_STORAGE in the Bluetooth...
Using a slightly modified version of the Zigbee Light Bulb sample app from the current samples compiled using nRF Connect for VSCode on a Mac and programmed to a nRF52840DK...
