Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
My understanding is that when the module's measured RSRP is lower than that defined in the broadcasted SIB, ECL will be escalated to higher level during RACH process.
Besides...
Hi,
I found out that my Matter device does not commission to Alexa because as part of adding the device Alexa will try to read FeatureMap attributes from all clusters and...
Hello! I'm working on some project using Fanstel BM832 module. I'm using the configuration based on board nrf52dk_nrf52832, with some minor modifications (led's and button...
Hi:
I'm doing the exercise L3-E1.
I used nRF Connect SDK Toolchain v2.7.0 because it didn't work with v2.8.0
How do I make NRF Terminal appear?
Thanks and Best...
I have a quick question about configure i2c.
I have the following schematic:
And the following configuration for the nrf54l15 :
And the following in prj.conf:...
Once the nRF52840DK is running the Zigbee light bulb demo I cannot flash new code to it unless I disconnect the board and reconnect it first.
I am using nRFConnect for Visual...
Are there user programable once registers on nrf5340 that I could use to store board hardware version? I looked at UICR, but I think they get erased when the whole chip is...
I added FOTA over Bluetooth to my NRF52840 application. Everything works, I can update the application over bluetooth and it runs properly, but after updating if I unplug...
Hello Nordic support,
I would like to understand how I can decrypt the packets that is using Legacy passkey pairing. Here is the BLE sniffer log, where I selected Legacy...
Hi my ffriends,
I’m working on a wireless system called for me " Wireless Link Project" , based on the nRF24L01 (non-Plus) transceiver.
I have two identical boards using...
Hello DevZone,
I have a confusing question about TF-M. Need help from a TF-M expert.
In this document , it says that we must disable uart1 in non-secure application, because...
I'm trying to test the overall pwoer consumption of my setup (nPM1034EK and nRF54l15DK) using the PPK2. As I've started this, I've gotten far higher numbers that I expected...
After I reset the kit (custom equivalent to nRF52DK) it advertises, and I can connect from the BLE Standalone App on my Windows computer. But it only advertises for a short...
I recently bought a fanstel blg840 device, and I have programmed At client firmware in nrf91 and custom code into nrf52, but the problem is nrf52 is sending at comments to...
