Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Trying to install NRF Command Line Tools. Platform is Linux 64bit x86 (distribution Ubuntu 22). I already have installed utilities by Segger, which may be the reason why NRF...
Question 1: I am using GPIO external interrupt. Does this interrupt belong to GPIOTE PORT EVENT by default? Question 2: How to configure low precision GPIOTE? Question 3:...
I use NCS2.5.0，and I noticed that there are two files(bluetooth.h and scan.h) can help to set scan parameters.Is there any difference betwen these two files?Can I call the...
Suddenly DFU OTA fails most of the time while trying to update units with code & "not secure" bootloader that has been working for years. The FW upload stops at 2% to 8% but...
Hi,
This is my first time designing RF section for BLE using nRF54l15, and i was wondering if you guys can give me some feedback on hardware design. I chose a Johanson 2450AT42B100...
Hi,
I am trying to optimize my nrf52840 application for power consumption. If I run simple loop using nrf5 SDK i get ~1.2mA. However with similiar code on Zephyr: I get...
Hi,
I am developing a small beacon application using the nRF 52805 device, and the intent is that it will send advertising packets at a slow rate, to indicate to a partner...
I'm working on implementing arithmetic operations using the PKA engine on the nrf52840 in Rust, following the CRYPTOCELL — Arm TrustZone CryptoCell 310 datasheet. While I...
Hello all,
I have been working on the implementation of the PKA engine on CC310, and have been encountering some unexpected behaviours when using the modular multiplication...
Hi,Nordic team
I am programming with nrf52833,ncs v2.9.0,base on peripheral_hids_keyboards and central_hids.
On central I call bt_hogp_rep_write_wo_rsp can only send one...
Hello,
Both nRF5340 and nRF7002 list minimum storage temperature of -40C. We would like to understand what environmental testing has been done to reach this storage range...
I'm currently developing a project using the Audio NRF5340 to communicate over BLE. All the modifications I made to the Audio DK app work in VScode with SDK 2.9.0, but recently...
Trying to work through using the FLPR for a virtual peripheral. I can infer things like the VTIM sets counter 0 and 1 to automatically buffer data in/out via the VIO setup...
