Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
I saw earlier post on this blog and viewed on-line video for LitePoint OTA tester that claims to work with all BLE chipsets. We have multiple designs with different DTM interfaces...
Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hello,
I need help regarding flash memory read on nRF52840 device, SDk16, SD=340.
I have using the fds libarary for memory read/write in my code for many years now. However...
Hi,
I'm trying to scan for coded phy devices with the nrf-sniffer application.
Followed the guide and installed nrf-sniffer with the nrf-util.
In Wireshark it works...
We are using firmware 1.3.6 on the nRF9160. During testing, I ran into the reset loop restriction. To quickly get out of it, I issued a AT%XFACTORYRESET=0 command. (We are...
Hello Nordic Team,
I am using nRF5340 DK as a debugger/programmer to develop firmware for the Fanstel EV-WT02C40C module. My goal is to use Wi-Fi (nRF7002) Wi-Fi scan, Wi...
Hello! I am trying to upload the basic applications to the Thingy:91 X from the downloads tab, here: https://www.nordicsemi.com/Products/Development-hardware/Nordic-Thingy...
Hi,
I just noticed that there's another issue with my project after upgrading from SDK 2.3.0 to 3.1.1.
I am using the 802.15.4 radio for low level packet communications...
Hi,
for a project based on the nRF54L15, we are evaluating the new single-slot DFU mechanism.
Using NCS v3.2.1, I am testing the sample available at: https://github.com...
Based on the DevAcademy here is my following setup using a custom NRF54L15 chip with the NRF54L15-DK devicetree with following overlay:
prj.conf:
CONFIG_GPIO =y
...
I'm trying to configure the nRF cloud log backend to aid with debugging of devices during field tests without the need for bulky UART harnesses to capture logs from the serial...
Hi everyone,
We’re trying to use UART1 on the nRF9151 DK in non-secure mode , mapped to the Arduino R1 connector. However, it seems to be reserved by TF-M , and we cannot...
Hi,
I want to reduce the time required to read 16 KB of data from the datalogger. Currently, it takes about 6 seconds to read all the data. How can I decrease this time...
Dear Support-Team,
I have checked that now back and forth: When I add
CONFIG_NO_OPTIMIZATIONS=y CONFIG_MAIN_STACK_SIZE=8192 CONFIG_SYSTEM_WORKQUEUE_STACK_SIZE=8192
in...
So I have this nRF5340-DK board where the Segger programmer/debugging chip is the same size as the nRF5340 SoC. It recently broke when I was moving and I am about to purchase...
Hello,
I am trying to measure nRF9151 current using Power Profiler Kit II, running Cellular UDP project on EVK and following the steps in:
https://docs.nordicsemi.com...
Hello
I am using nRf52805 based BLE peripheral using the Nordic UART Service (NUS). The device transmits numeric data periodically using GATT notifications (NUS TX), and...
