Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hi, I am using NRF connect sdk 2.6.1 and I am wondering what is the best way to run crypto operations when using TFM profile type minimal and building for nrf9160_ns. TFM_PROFILE_TYPE_NOT_SET...
Hello Developers,
my name is K.hemasundar, Here i am using nRF52833 micro controller with segger embedded stdui IDE. I have a problem with the Ble_HID_Mouse example code...
Hi Nordic support:
Our product uses nRF9151 module, we are going to do GCF certification field test. Could you provide some guidance on the following issue?
How can...
I am using nRF52833 PCA10100 board. While trying to run sample ble code in segger embedded studio, I am frequently facing this error which says, .text file is larger than...
I am setting up Segger Embedded Studio on my M2 Macbook and running in issues.
I downloaded S140 (nRF5_SDK_17.1.0_ddde560) and upon the build, I see the following errors...
I have a nrf9160dk that drives a screen via SPI, using an IT8951 controller. The firmware driving the screen works fine if I plug the USB cable on a power bank or using MS...
Hi, I'm getting an error when building the example program blinky that says: ".text is larger than specified size" and ".rodata is larger than specified size".
I'm using...
I'm following the steps in exercise 1 of the nRF Connect SDK Fundamentals and getting configuration failures. From what I can tell it looks like Zephyr is failing to build...
nRF Connect SDK v3.2.0
Write code:
Read code:
Log:
The address seen on the phone is usually not "06 05 04 03 02 01", but sometimes it is "06 05 04 03 02...
After the PPK II had been stored for a long period of time, it was recently taken out to measure current. It was observed that, regardless of whether Source Meter mode or...
Hi all,
I have been attempting to get the nRF Connect VS Code extension setup to try out some samples on the nRF9161-DK board.
I'm currently having a problem with a version...
Clarify the minimum mandatory external connections and pin/rail requirements for an nRF9151 to boot and run a flashed application, and determine why serial_lte_modem (SLM...
Hi,
I'm working on an application that I recently updated to ncs v3.1.0 (from v2.9.1). For most of the development, I have been working with the nrf54l15 as build target...
HI
I have replaced the external flash used with the nRF54L15 with a different model. How should I set the sfdp-bfp parameters for this new flash?
Thanks!
