i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
How to configure the SPIM if i have defined my MOSI/MISO/SCK pins in the device overlay file, shown below:
&pinctrl { spi0_default: spi0_default { group1 { psels = <NRF_PSEL...
We are developing a board with an nRF54L15 module that interfaces with a SPI device. We want to use 3-wire spi, so the MISO and MOSI lines are shorted (according to the datasheet...
Hi,Team,
I am developing the nrf54l15-dk, and the version of my NCS is v3.0.2.
I am currently using Pawr. https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides...
Hello Nordic Support,
Currently, we are using nRF5 SDK for Thread and Zigbee 4.2.0 for our Zigbee coordinator application running on nrf52840.
We understand that this...
I am using the NRF5340 Audio DK , and the onboard PMIC is the NPM1100 . I am not using the onboard audio codec of the DK. Instead, I am powering an external audio codec module...
Hi,
I've just completed Lesson 2 Exercise 3 and found that BLE Provisioning does not work from the iPhone version of the app. The problem seems to be related to Version...
Hi everyone,
Environment:
nRF Connect SDK v2.8.0
Light Switch example
I’m currently working on implementing a Zigbee Sleepy End Device (SED) for a battery-operated...
Hello,
I'm currently using the nRF9151-DK hardware to develop our product based on the nRF9151 SiP . We selected the ncs-serial-modem firmware, and the modem is controlled...
I am implementing the code for nrf54l15 nordic MCU to: Use vbat_mon pin p1.10 in NRF54L15 as ADC and trying to read the voltages, but physically i am not able to read/get...
Hi,
I'm using nrf54l15 SOC with Zephyr NCS SDK to build a BLE application. I want to set the radio Tx Power to be set to as high as possible as our device will be enclosed...
Hi There.
I been 15 year experience in embedded system development but I'm very new to the Nordic nrf environment.
I'm eager to learn and develop some product and provide...
Hi, I have a nrf54H20 board rev 0.9.2 and I followed the https://docs.nordicsemi.com/bundle/ncs-3.0.0/page/nrf/app_dev/device_guides/nrf54h/ug_nrf54h20_gs.html#nrf54h20_dk_bring...
Hello, We are currently working on designing a CS-based distance estimation algorithm, referencing the two example routines, `ras_initiator` and `ras_reflector`, from NCS...
I'm getting exactly the same as this ticket now I've switched to extended advertising. Was there any resolution?
Android is fine, iOS 18.5 phone sits in a connect/error...
I'm testing the spi communication protocol with the nRF54L15 DK. At that moment, I'm testing the lesson5-exercise 1 solution of the intermediate course. The problem appears...
