Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
NCS 2.7.0
nrf52840
I'm currently porting software that was originally developed for nrf52832 on NRF5 SDK to run on Zephyr. I am currently on a deadline to delivery a prototype...
I am trying to run the sample using NCS v2.5.0. This is what happens on the console when I try to connect from the dongle, when running the Test Procedure:
The discovery...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
Hello,
I recently migrated to SDK version 3.2.0-preview, which supports Matter 1.4.x.
When I use ZAP and add a new endpoint to the light_bulb example under the name Electrical...
Hi I'm trying to communicate with ICM45686 using nRF54H20 and SPI CLK, MISO, MOSI state appear correct but CS pin is not asserting/deasserting following it the scope capture...
Regarding the nRF54L15-DK development board and its use with BlueZ on an Ubuntu virtual machine: After flashing the hci_uart example onto the nRF54L15-DK board, I used the...
I’m working on a project using the nRF54L15 SoC together with the nPM1300 Power Management IC . In my hardware setup:
BUCK2 output from the nPM1300 is connected to the...
Hello, I am facing an issue in nrf52dk (nrf52832dk). Whenever I access i2c0 bus for the controller it works fine but whenever i switched on the i2c1, it starts giving me device...
Hi, I`m working on a custom board. I have been playing around with it for a couple of months, but just recently stumble upon a strange behavior. This is a custom device where...
Hi, I am trying to use the external flash on the nRF54L15 DK with QSPI to perform the zephyr/samples/subsys/fs/fs_sample sample.
I am using NCS v3.1.0 (on Windows if that...
I’m working on a project using the nRF54L15 SoC together with the nPM1300 Power Management IC . In my hardware setup:
BUCK2 output from the nPM1300 is connected to the...
I currently evaluated the use of the "<modem/at_parser.h>" (at_parser module).
Using it with the at-cmd "at+CEINFO?" is very irritating.
I 07.324 : CEINFO: +CEINFO: 0...
Our team is transitioning to the nRF Connect SDK after extensive experience with older nRF SDKs and custom build systems (based on cmake + west + python) integrated with VS...
