I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
hi i use pca10056 board with segger embedded studio
i currently facing a bizzarre problem with my project
i use adc function and nus service and low frequency clock
...
Hello i realize the nRF24L01P is NRND. Curious if you are able to answer w/out too much work as to whether one of the other nRF devices allows access to the radio to use the...
Hi:
I set up a fresh install of the NRF Connect Extension Pack in VS Code on my MacBook Air M4 and was able to build and flash the Blinky demo to my nRF52840DK. The issue...
Hello, this ticket addresses three issues:
1. After installing nrfutil with subcommands device and toolchain-manager and sdk-manager, into %USERPROFILE%\.nrfutil, everything...
Hello,
Since our Product Launch we have gotten feedback that pairing with some (but not all) Apple devices is a significant problem. Even through several attempted fixes...
After upgrading nRF Connect SDK from 3.1.1 to 3.2.1, our fixed regulator stopped working. We are on nRF54L15. Tracking it down further, this seems to be some sort of GPIO...
Hi,
I am porting a product from SDK 15 to SDK 17 and to Nrf Connect.
We need to maintain code combability as far as possible between products using SDK 15/17 and products...
I'm creating a system test for manufactured units and if it's OK I would like to set a permanent flag in an area that will not be erased if I erase flash at a firmware update...
nrf sdk 17.1 example:peripheral/uart/pca10040 I attempted to use P0.9 and P0.10 on the development board to set up a UART serial port for data transmission and reception ...
Hi,
I am on NCS 2.9.0, I have tested lesson 5 exercice from NRF Intermediate course about BLE DFU, I have some questions about it:
- with mcumger, is there a way to update...
Hello,
We have a custom board we are developing on that uses the nRF54L15 MCU. The board has some LEDs that we were hoping to drive using PWM, but these are connected to...
Hi all
I have some trouble with a new batch of nRF9151 chips.
The old one had the Firmware: 2.0.2
The new ons have the Fimrware 2.3.5.
My application does no longer...
Hello
I tried to test OTA function with smp_svr example.
I want to use the external flash mx25r64 on nrf54l15-dk(v0.9.3) to store update Firmware over BLE. SDK version...
Hello,
I have some unclarities for the APPROTECT mechanism on NRF9151.
Basically, I had a misunderstanding of the involved CONFIG features, and as a result I used CONFIG_NRF_APPROTECT_LOCK...
Hello,
I’m using an external NFC reader/controller (NXP PN7160A1HN/C100E) connected via I2C to an nRF52840 module (Raytac MDBT50Q-1MV2) on a custom PCB. (Programming is...
