I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
I have tried compiling peripheral_hr in Zephyr, as well as flashing the heart rate demo binaries.
All give the same result - the board simply resets as soon as BLE Advertising...
Hello,
I'm trying to connect as fast as possible two devices (central : 52832 S132v5 and peripheral : 51422 S130v2), for a given advertisement interval. The central will...
People tracking and fitness trackers. Hello. Sorry for beginner question. I trying to develop a real time location system to track people (using rssi) and take data from their...
I'm attempting to perform DFU with the secure bootloader (bonding not required) and it is hanging after starting the update. Here's the log from the firmware (SDK 16.0.0)...
Hello,
I am developing an app which connect to provisioned node using GATT in the mesh network. But the limitation of this is, it has only pair to pair communication. It...
Been beating my head against this for a couple of days and came across a number of people on the forum with the same issue without a solution, so hopefully this saves someone...
Hi all,
I have some issue setting up the advertising data on my nRF52840 Dongle. I'm using the ble_template to develop my software and in my application i need to fill all...
Hi all,
can i send a scan request from an nRF52840 dongle using the nRF Connect - Bluetooth Low Energy software? I need this during development of my application where i...
Hi
I am seing framing errors when receiving using UARTE.
It is not external hardware, I have checked with different other interfaces and measured timing, no problems there...
Hi
I want to ask a few question.
When the phone sends a specific signal after connecting to the MCU, the MCU is sending data in real time.
When the power is turned...
Hi,
I was trying to find out if it is available to have authentification before connection and I found this link and it makes sense to me but that Q&A has been over 4 years...
Hello!
I use Zigbee CLI example and multi_sensor example on nRF52840. (examples/zigbee/experimental/cli/cli_agent_router and examples/zigbee/experimental/multi_sensor) ...
I have nrf52840 dongle and sdk nRF5_SDK_17.0.0_9d13099.
I would like to know, is there is an example in which, Advertisement Data is stored in flash memory and reading and...
I USE 9160 with i2c ，send data. then it tips :
[00:02:07.716,918] [1;31m<err> i2c_nrfx_twim: Error 195952641 occurred for message 0[0m
what is wrong ?help me ,thank...
