Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hi,
Is there any sample Android mobile application available which calls or consume the Temperature/humidity for nrf5_SDK_for_Mesh_v3.2.0 ?
Best Regards,
Hi,.
I am using nRF52832 , sdk 16V
How many samples can be sent over ble if we set 7.5ms minimum
I need to send the 100 samples. I tested by setting to it 7.5ms I think...
H i everyone, I'm having a problem as follows: I am wanting to use LPCOMP to wake up the nrf52840 from system off mode. So can anyone give me an idea of how to do that?
I tried Searching for the NRF_CCM structure, but could not find it.
Where should it be nor the MAXPACKETSIZE.
this code is in the system_nrf52840.h
Also, could you please...
Hi
We are doing field trials of a nRF52840 product with s140 SD, now and again NFC stops working (tag type-4, read and write).
This has been seen in SDK15.3.0 with SD6...
Hello,
I would appreciate some guidance about BLE connection stability. Our product is a system of 3 peripherals (custom board with Laird's BL652 module, containing nRF52832...
Hi,
I have a project which requires using trace data pin P0.18 as an SDA for the sensor, but cannot send
anything because it doesn't generate anything and the program...
Hi, we are moving from nRF52840 DK to integrate nRF52840 to our solution. In the datasheet for pin assignments ( Link ) it states "recommendation usage; Standard drive, low...
I'm currently running nrfjprog version on OSX. Version info below:
When running a nrfjprog -e I expect that the device doesn't do anything afterwards. When monitoring...
I'd like to use two nRF9160s to do D2D (Device to Device). Is it possible? For example, if you press Button 1 on nRF9160 (1), then LED 1 on nRF9160 (2) is displayed. Is it...
Hi,
our company is developing some different models of devices with BLE based on the nRF52840 MCU, working with the nRF5 SDK (17.0.2). The devices are in parallel using...
Hi All,
I am working on the nRF52840 Zigbee protocol and I am using nRF5_SDK_for_Thread_and_Zigbee_v3.0.0_d310e71 SDK.
With the help of engineers and other stuff, I am...
I updated the nRF Connect SDK to latest master. It currently uses Zephyr 7d20f2ebf2. Most of the time (~4 times out of 5), calling sys_rand32_get() crashes the firmware and...
Does the ZBOSS stack have an API that provides network statistic or network health details? We would like to get a general understanding of state of the network.
Thanks...
Hi
I'm using SDK_17.0.2 with softdevice S132_7.2.0, can anyone advise DFU SD version code for this?
I can't find it in list below, the last version is S132_7.0.1, thanks...
