I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi, My PC have already installed the nrf connect sdk with version v1.2.0. How can i update the nrf connect version to v1.2.99-dev1? Please give me a few complete steps .
Hello everybody, i am trying to use BLE central uart sample software in zephyr, on nrf52840 dongle. I mapped the uart outputs on pins 20 and 24 of the connector, made the...
I have created custom characteristics by
BT_GATT_SERVICE_DEFINE ( vnd_svc ,
BT_GATT_PRIMARY_SERVICE (& vnd_uuid ),
BT_GATT_CHARACTERISTIC (& vnd_enc_uuid . uuid ,...
I am using the current nrf-sdk v2.1.0, which includes the matter version v2.1.0 from the Nordic repository.
I encountered an error that setting CONFIG_DEBUG will result...
Hi
I have successfully used the TIMER & GPIOTE to generate dual tone frequencies for a BFSK project. 200kHz & 400kHz. ( 50% duty cycle square wave)
I wonder if the same...
Hi,nordic
I am using 52832. The SDK is mesh500 and sdk1710. I want to check the data sent from the PC through the serial port. Where am I and how do I read the data?
I am using the NRF52 development kit and I modified the uart example main.c to simple TX and RX application using printf function. The board is directly connected to the PC...
Good morning,
I ended up changing the design to use the nRF52810 chipset and I wanted to find out if Nordic would be able to provide some schematic feedback for my design...
Hi Nordic expert,
We are K5DET1/3/5/7/9/11 output high level, then string 10K resistor, K5DET2/4/6/8/10/12 through the mercury switch to read this high level, while adding...
Hi,
According to the documents of NCS, CoAP Server sample uses native OT CoAP API while CoAP Client sample uses Zephyr CoAP API, and the Zephyr CoAP API is recommanded....
I've googled all over, and I'm having a hard time finding any documentation that digs into how to use the nRF Connect SDK. Most documents point to examples, however the wealth...
Hi，
I developed with ncs 2.1 samples esb ptx and prx using nrf52840 make a low latency application，There are two problems
①On the ptx side, packets are sent twice in...
Hi, in our project we have to send some raw data to one node to other node using zigbee. So i have checked every single example but it doesnt match with what i need. I have...
Hi,
I'm trying to write a simple python application on Windows 7 that communicates with a BLE peripheral running Nordic UART Service. I'm using the nRF dongle and pyserial...
Hi,
I'm trying to config my SAM-M8Q with an array of HEX.
It's work beautifully with app_uart_put like the picture below.
However, when I try to implement LIBUARTE...
