I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
I am looking at the example of the HRS collector (Central) of the SDK also called ble_app_hrs_c.
In the file nrf_ble_scan.c in the function nrf_ble_scan_on_adv_report we...
Hi,
I am using ble_app_beacon with Softdevice S140 with SDK 17.02 for nrf52840.
In the example code I want to set beaconing to only one channel (channel 39) and be able...
Hi Nordic Team,
when discovery custom 128bits uuid service, I have high probability get BLE_GATT_STATUS_ATTERR_ATTRIBUTE_NOT_FOUND, but sometimes I get BLE_GATT_STATUS_SUCCESS...
Hello,
I am upgrading my project from SDK 15.0 to SDK 17.0 and I get this message.
Please see my project's comfiguration file:
debug_additional_load_file="../SDK_17...
Hi, all
I'm trying to i2c(twi) in low power..
In this case, I want to generate an interrupt through the i2c read function " read_touch_data " (under code).
Where...
Hello team,
We have a sensor design based on nRF52840 and currently we have configured it in the normal voltage mode DC/DC REG1 enabled. It is a battery operated design...
hi,
I am using nrf5340 dk board and nrf connect sdk. i want to encrypt the data and decrypt the data in application core. I have seen cryptcell 312 for cryptohraphic algorithms...
Hi,
I am currently working with the nrf52840, ble_app_uart example under the ble_peripheral folder. Using the tutorial below:
https://devzone.nordicsemi.com/nordic/short...
Hi,
I want to receive data on BLE and send it through USB to PC, I am using SDK17 and nRF52840 dongle. I send data from the transmitter with nRF52832 through ESB configuration...
Hi,
I'm currently developing the code of a RGB led lamp. The thing is, when I change the color while sniffing with Wireshark, I see only 1 payload (the way it should be...
How to easily migrate SDK to SDK, (Lower to Higher) or (Higher to Lower).
I mean from SDK 14 to SDK 17 or vice versa.
Please answer this as soon as possible
Hi,
I am pretty new to telecommunications and AT-commands in particular. What I want to do is:
-Scan all nearby base stations (BS), and read all available information...
Hi.
I'm developing a sensor driver for the Spec Sensors DGS-O3 968-042 UART gas sensor for the nRF9160 (Thingy:91 to be precise)
The general gist of it is that I need...
If we want to make certain that a particular message goes first on a connection interval. Is there a way to check that there is none already internally queued?
Is this...
hi i am using nrf52832 sdk v16, i need to print a data using uart example got a issue it's not getting app_uart_put & get function not working but printf() function data are...
