I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello, I have a question.
I am developing with nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral.
I have a question about the output time of the advertisements. The...
Hi,
I am develloping product witch ICM20948 and need to use magnetometer. I tried to move some existing and working code for arduino. I was able to get data from magnetometer...
Hi,
Our customer is optimize the size of flash used of nRF5340.
They are curious whether the definition in autoconfig.h are all used in the image? or some of them are...
I am testing nRF5_SDK_17.1 examples/dfu/secure_bootloader/pca10040_uart_debug
After I run on SES. I got this memory map. It overlaps softdevice area.
With armgcc ...
How do I use printf to output my own messages, and read incoming data, from a UART port that is separate from Zephyr's debugging outputs? This UART line will be connected...
Hello, we are trying to get software running on our custom board.
Last week we tried to test the software written on a development kit of the NRF9160 on to our custom board...
Hi.
I'm trying to add a SPM partition to my project. Like another project i did in the past, i followed this guide: https://devzone.nordicsemi.com/guides/nrf-connect-sdk...
We would like to know there is any direct test mode for TX power of NRF21540DK.
We only found the method of nRF52833 direct test(TX). But we can find how to do with NRF21540DK...
Hi,
I wonder how to use the internal capacitor of the nrf5340.
The nRF5340-DK operates at 32M=8pf 32.768k=9pf without any special settings.
If i use 10pf products for...
Hi,
I'm porting firmware between nRF52 and nRF53 platforms. What is the equivalent of NRF_UICR-> CUSTOMER on nRF53 to keep data like serial number etc.
Thanks
Sebas...
We are developing a custom device based on the nRF9160 SiP Revision 2 with multiple connections over LTE-M and we are experiencing problems with keeping our only TCP connection...
Hello, I'm using nrf mesh serial example in nrf5sdkformeshv500src, in the serial node i subscripted to 0xC000 but i can't not received messages more than 32 node, my netwwork...
Hi All,
Sorry to ask this question, I just learned a little about cmake.
Now I wanted to add a few src files based on the light switch example in SES. Do I have to create...
Hello,
I am working on developing a BLE peripheral FW (Reader) with NRF52840 using nRF Connect SDK 2.0.0. The Reader has two MCU, one is BLE MCU and other is the main...
Hi.
I am trying to update my Softdevice using DFU.
If I update from S112 to S140, do I have to upload the application as an image built with S140 as well?
And do I need...
