Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hello Group,
I got an error when I tried to “Open nRF Connect SDK Project” from the Segger Embedded Studio.
Do have any idea how to fix it? (the attached here my process...
Background:
Custom boards
SDK 15.2.0
SoftDevice: s140_nrf52_6.1.0
Hello,
We recently updated our project to use 2M PHY instead of the default 1M PHY. Our device...
Hello!
When looking at the central example ble_app_multilink_central in sdk_config.h, I found out that all links are considered central, with NRF_SDH_BLE_PERIPHERAL_LINK_COUNT...
Since the beacon will run on CR2032, I'm trying to minimize power concumption.
NOTE: All measured using nRF52-DK + PPK2 configuration
The online profiler says that if...
Hi all,
I have evaluated the performance with ble mesh on nrf52840 board on zephyr system.
when I use ble sniffer(wireshark) to catch the package I fond that every message...
Hello sir ,
I have successfully uploaded hello_word code from sample and i got" Hello_word" printed on lte monitor 's display using nrf9160.
now am trying same thing with...
Hi,
I would like to use the Event Manager for a product that is currently planned to use a Nordic product; however, I would like to be able to port the firmware (or parts...
Hi,
I am using ncs 1.5.2, and want to create a FOTA image. I am successfully able to build, flash and confirm the image, but am unable to set the version number of the image...
This is the errors , please help, to successfully create .hex file
If you want to look after full log details .......
Building firmware west build --build-dir c:\Users...
I bought a thingy91 module with ibasis scheduler on board. When I made the first installation of the mfw_nrf9160_1.3.1.zip software and the thingy91_asset_tracker_v2_ltem_2022...
I'm building a simple application using I2C to read sensor data (BNO055). I confirmed I2C and my sensor are all configured appropriately and working smoothly, but when I added...
Hi,
I'm using the mqtt_simple example to develop a new application.
I want you to tell me what lines of code I need to add for the nRF9160 to work in the minimum power...
Hi,
I am working with NRF52840 DK, from this i am using KEIL IDE. I got some error while opening the KEIL SW like Cannot set path to software packs. Make sure that RTEPATH...
Hi,
My customer use nRF5340 as their master control IC, which will connect with lots of peripheral.
They are considering about simulate a uart with GPIO.
What's the...
I have designed a custom board for the nrf52840 and upon testing it in the nrf connect sdk (using a JLink), I can only see the board when it's in bootloader mode. When it...
