Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
I have encountered a problem with I2C bus on the nRF54L15. BMP390 sensor is connected to nRF54L15-DK by the i2c bus. if i try to brake the line and recover it agane, the connection...
In nRF5 SDK, we configure GPIO wakeup sources for System OFF using `nrf_gpio_cfg_sense_input(pin_number)`.
What is the **exact equivalent API/configuration** in **nRF Connect...
Hello.
I'm trying to use a nrf52840 as a central device and connect to a gopro13. The connection works a certain number of times. But after a while (several days or maybe...
Hi all,
this is a bit embarrassing, I updated from nrf SDK 2.5.0 to 3.1.1 and I'm a bit lost with the simplest things.
I need to toggle an LED on a custom board. I'm using...
We are using part nRF52840QF (QFN package, not aQFN) as part of new designs as it has the following improvements compared with the nRF52832:
Output power of +8dbm
Extended...
Hi,
I’m having trouble getting the Matter Test Harness to run.
Environment
rPi 5 set up per Matter Test-Harness User Manual.pdf (using project-chip/certification...
Hi, I'm trying to install modem fw using the script given by Sigurd : https://devzone.nordicsemi.com/f/nordic-q-a/53208/updating-nrf9160-modem-firmware-through-the-command...
Hi. I have a new project using zephyr 3.5.0 and ZMK, so I don't think NCS SDK is an option. I am using pca10056/nrf52840dk
I am trying to configure I2S, and the examples...
I am currently experimenting with the nrf9151DK and was hoping to mimic a LTE-M sensor that would wake up once an hour, send a message over CoAP with DTLS, then go back to...
Hello, I have problems in the async-mode with the UART21 output and the nRF54L15. I am using Toolchain v3.1.1 and SDK v3.1.1.
When I use the uart_tx function to print out...
Hi
Is there a specification of running the nRF21540 in Tx mode at 10 dBm and 20 dBm with no load connected? Will the reflected signal cause damage to the PA and if yes,...
Hi Support Team
I tested matter bridge sample running on the nRF7002DK with peripheral_lbs sample running on the nRF54L15DK.
Application guide
Then I encountered problems...
I am working with the nRF9160 DK (PCA10090) and would like to use the onboard nRF52840 interface MCU as a host controller for an external peripheral.
From my understanding...
I am using the nPM2100 EK dev board with a stm32wl5MOC.
Using the example from the bare metal drivers, I adapted the code to my board.
I can succesfully read and set bytes...
currently this is more of a theoretical question, but i have an idea of something that might utilize this (3 QSPI devices)
Ive been looking at the Nrf5340 and the nrf7002...
