I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I know from zephyr samples that Tensorflow lite is available via zephyr as an external module, though it's not explicitly allowed in the nrf west.yml, and therefore is not...
Hi all, I follow example (serial) to build and run, i already run successfully, but i meet some question. when i use generic_on_off to control light at short time(2s), the...
Hi,
On a NRF52840, I try to perform `x` SPI transactions of 3 bytes each using EasyDMA Arraylist feature fully controlled by hardware. The CS must be toggled between each...
Dear Nordic Experts, The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832. When provisioning, it sometimes...
Hello, All
I am trying the scan_adv example, and use my phone to scan the advertising packet, unlike other peripheral examples, I found that it appears multiple time with...
ncs v1.9.1
Reference nrf\applications\serial_lte_modem\src\twi
This example does not see how to configure the pin.so how to config SCK and SDA Pin?
Thanks!!!
Is it feasible for me to use the 9160 as ble-host and 52820 as ble-controller using just TX and RX lines? (no request or ready lines) My setup is NCS v1.7.0, custom board...
I see that there is definitely support for where a user would cancel the USB host's request to suspend inside of app_usbd.c here's line 1246:
You can clearly see that it...
Hi,
I know that a GPS receiver can can use the Doppler effect to get an accurate velocity measurement. More accurate than the accuracy for position.
However, from my tests...
Hi,
I'm facing the mqtt error shown in the image below "E: mqtt_connect, error; -111" when I try to establish connection between the nRF9160 DK and AWS Cloud. I've double...
Hi,
I am required to develop a new model, upon design considerations I considered that my main BLE-Mesh model will have 3 independent sub-models each designed as per functionality...
Sorry if this is a repeat ticket. I've done some searches and they result in information around Zephyr and RF Connect SDK Git repos and West usage to manages related source...
Hello,
I am using MQTT+TLS on nRF9160DK. In the development stage, I followed this link https://devzone.nordicsemi.com/guides/cellular-iot-guides/b/software-and-protocols...
Hi,
Mesh SDK: v5
Using nRF 528232
I am trying to implement a low power node feature on an existing PIR sensor code. I have added all the necessary functions and macros...
I started off my project with the Zigbee light_bulb sample, and I added some new functionality that needs to manipulate various GPIOs. These GPIOs are neither buttons/keys...
