Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
I am using the older SDk 17_1_0 used in the Qorvo UWB sdk.
nrfConnect ->connected to -> controller ->connected to ->beacon, neither appear in scanner as expected once...
I can't define an Advertising file larger than 191 bytes, even in Extend.
Here's my code and proj.conf file.
My board is an NRF52840.
main.c
proj.conf
E...
Hello,
I'm working through the fundamental courses and trying to get my nrf54lm20 development board setup. After I have built and flashed the sample firmware to the dev...
I just upgraded my project (that runs on custom hardware with the nRF8233 using an Ezurio BL653 module) from nRF Connect SDK v3.1.0 to SDK v3.2.1 and the battery monitoring...
Hi, we have recently started developing with the nRF5340DK. We encountered several issues while configuring a FATFS on the external flash (mx25r64).
1. The sample code...
Hello
I am currently trying to develop an asset tracker based on your Asset Tracker Template ( GitHub - nrfconnect/Asset-Tracker-Template · GitHub ). While going through...
Hi,
I am trying to configure SWO logging in a sample project based on zephyr/samples/hello_world (source and config at the end).
I run this application on two targets...
Hello,
In document nRF54L15_qfaa_4L_config1_pcb_reference_layout_0_6 there is a representation of the PCB with 4 layers. The GND of C9 is not connected on the top layer...
Hi,
When configuring an nRF54LM20A for usb and then using the `onoff_request()` API to enable the HFCLK after that, results in spinning sys_notify_fetch_result() forever...
Hi
I am currently experiencing an issue with my custom board related to poor BLE signal performance.
My devices are based on the NORA-B101 (nRF5340) combined with a SKY66408...
Enable the "mcuboot_with_encryption" function. 1: When using VSCode for flashing, by default, mcuboot is flashed with un-signed and un-encrypted firmware, while the application...
Hello team,
I wanted to implement direction finding using BT for nRF5340 available in Thingy 91x.
Please let me know is it possible to implement or any pre available examples...
Our company is developing second-generation implantable medical devices and plans to use the nRF54LM20A chip/component. We place a high priority on product reliability, so...
HI,
I am using "NRF_POWER -> TASKS_CONSTLAT = 1 ;" to enable CONSTLAT, but when i printf("TASKS_CONSTLAT %d",NRF_POWER->CONSTLATSTAT); the result is still 0; how can i...
We are using the Asset Tracker Template with on a nRF9151-SMA-Devkit, using the enclosed external GNSS antenna outdoors (out of the window) and the GNSS reception is very...
