I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
I get this error after creating a custom board
C:/ncs/v3.1.0/nrf/subsys/mpsl/init/mpsl_init.c: In function 'm_config_clock_source_get': C:/ncs/v3.1.0/nrf/subsys/mpsl/init...
I'm attempting to put together an application using the baremetal version of NCS just released... I need these to run DFU over BLE so we can update in the field.
I created...
Hello,
I am experiencing a recurring issue when programming multiple nRF52840 boards using the nRF Programmer.
Problem description: When programming the first board...
Hello, I have a pin that controls the power flow to the sensors on my board. it is active low, when it gets a raw value of 0, it allows the power flow to the sensors. I have...
I have just upgraded my project to NCS 3.1.0 and I'm now getting this error
BOOT_SWAP_USING_MOVE (defined at C:/ncs/v3.1.0/bootloader/mcuboot/boot/zephyr/Kconfig:575) set...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hi, I am working on storing data in the Trusted Zone using the PSA APIs.
I tried the Protected Storage (PS) example. When I store data using psa_ps_set() and then read the...
I am updating our automation software for programming Thingy 91 and trying to communicate to ModemShellRtt using python. In my test program attached, I would only like to...
Hi all,
I am working on a project to remotely control iPhone cameras via Bluetooth. I can already emulate the shutter button using the Volume Up command (0xE9). However...
Is it necessary to Update nRF SDk and Toolchain each time a new version comes, can't I use one version constantly. As with each update some libraries are getting removed or...
Our setup:
Board: nRF5340 DK
SDK: NCS v2.6.2
Microphone: MMICT5837-00-012
Interface: PDM
During mono audio capture over PDM, we observed a current draw of about...
Hello,
we are developing few products based on the nRF52833 and we found something interesting in the nrf52833 dts file ( https://github.com/nrfconnect/sdk-zephyr/blob...
Hi Nordic Teams,
Now I'm using Nordic Connect SDK v3.1.0 to development, I want place some default values in Flash at a fixed address,
But I don't know how to do it...
Building the sample "nrf/samples/cellular/udp" with "west build -b nrf9160dk/nrf9160/ns" using
NCS 2.9.2 results in:
Memory region Used Size Region Size %age Used FLASH...
