Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello,
after an attemp to switch to UF2 Bootloader from Open Bootloader my Makedriary nRF52840 MDK USB Dongle stopped working (now shows only the green led always on) and...
Hello ! I'm trying to adapt the code from the master-slave SPI example ( https://github.com/too1/ncs-spi-master-slave-example ) for my nRF54L15 development kit.
The master...
hello,
I would like to know which operations were performed on all chips by the `nrfjprog --recover` command.
"The nrf52833-B chip is by default enabled for read protection...
Hi
I am getting an error while building source code. The same code used to build while using NRF connect SDK version 2.5.1. Currently I am using nRF Connect SDK version...
Hi,
I followed the steps below and the error "zephyr\zephyr_pre0.elf section 'text' will not fit in region' FLASH'" appeared when I compiled. I did not change any code....
Hi, I am working on a Bluetooth Mesh project for lighting control using nRF5340. I am currently stuck on how to implement a Bluetooth Mesh gateway for my mesh network. Here...
Hi Nordic,
In my project, I have a NRF9160 and a NRF52832 with a ble host/controller stack over SPI HCI on NCS v2.5.2 As soon as I activate the HCI SPI in my project, the...
I have bought an nrf9161-dk and following the documentation, I was installing the asset tracker using nrf-desktop v.4.4.1 (because v.5.0 crashes everytime I open it in full...
Hi, We are using `fota_download` library on our nRF9161 design running mfw-nrf91x1_2.0.1 to download a firmware upgrade image from our Amazon AWS server location. When trying...
Hello, I am currently using (\nRF5_SDK_17.1.0_ddde560\examples\peripheral\radio\receiver)routine to develop.I want to check if the first N bytes of the received packet are...
Hi! I am using nrf32840 with free rtos,
and I have a loop that do the following
for(;;){
vTaskDelay(pdMS_TO_TICKS(intervalTime)); // go to sleep due to portSUPPRESS_TICKS_AND_SLEEP...
Hello guys, W are using the nRF52840 development kit in our project, we received the development kit today and when we powered the kit to my laptop(Acer nitro 5) using a micro...
Hello guys
I'm using nRf52840 development for my project, when trying to connect using a micro USB to the laptop, the J Link drive is not being detected on my laptop(Acer...
Hello.
In the BLE software being developed, the device uses nRF52840, s140 v7.2.0 or v7.3.0, and I am building a system that periodically sends a beacon (ADV_NONCONN_IND...
I am trying to program nrf52840 to print acceleration from mpu6050. But when I build the project, I get the error - undefined reference to `nrf_drv_twi_init'. Here is the...