Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi, Iam working on a project based on BLE Mesh, Iam using nrf5_SDK_for_Mesh_v4.2.0_src. Iam trying to form a BLE Mesh network and control the light bulb. I would like to control...
Hello, I am receiving error code 40412 when I attempt to activate my nRF9160-DK board. Following other similar DevZone tickets has not resolved my issue. My steps so far and...
I'm trying to build the smp_svr example design: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/samples/subsys/mgmt/mcumgr/smp_svr/README.html#smp-svr-sample...
Hello,
With UDP Sample switched to c++ (main.c -> main.cpp and added CONFIG_CPLUSPLUS =y, CONFIG_LIB_CPLUSPLUS =y) i get compilation error on including lte_lc.h
In file...
We are implementing a system where diagnostics info is saved to FLASH when one of the error handlers is called. Our code collects diagnostic registers and stack info, and...
Hello,
I am working on a driver in which it needs to transfer larger sets of data over a I2C connection. However, I am getting this:
"Cannot copy flash buffer of size...
Hi，
Q1: SDK for PCA10112:
I'm trying to evaluate 21540 DK and EK set. Where do I get sample code that compatible with PCA10112? I've checked the latest nRF5 SDK 17.1...
There are several questions regarding this, most recent I could find from 6 months ago ( https://devzone.nordicsemi.com/f/nordic-q-a/81686/is-there-support-for-gatt-caching...
Hi,
I would like to know if I can update the firmware of modem from 1.1.1 to 1.3.1 on Thingy91 (hardware version 1.4.0).
My goal is to use AGPS and PGPS assistance services...
The product specification states that "o nly the dedicated QSPI pins shall be used. " Is this a recommendation or a requirement? I would like to configure a different pin...
I accidentally closed the original ticket , so I create a new one.
Hi,
recently I'm building dfu function on my board, using nrf51822 qfaa and softdevice s110.
...
hello,
Im using nrf52840 Im trying to emulate a chip select signal for spi slave with gpiote and ppi. I used an active high signal as an event and a signal(cs) that is toggled...
Hi everyone,
I have some questions regarding RSSI:
1. Is there any Bluetooth reference that evaluates the RSSI? For example what RSSI range is considered as perfect, moderate...
env:
SDK: nRF5_SDK_17.0.2_d674dde
KEIL- ARM
SoftDevice： s140_nrf52_7.2.0_softdevice
i can't understand how MBR jump to bootloader, and how MBR konw the start address...
