Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hi
I'm using a SparkFun Pro nRF52840 Mini which has a UART on PIN 17(TX) and 15(RX). I've written a very simple piece of code to blink the onboard LED on and off and to...
I update my software on the nrf52840 to the SDK16 and softdevice 7.
to get this software running i update the device family pack to version 8.29.0. (keil)
If i build the...
Hi,
There's no description at all in either the written text (31.3 SPI master transaction sequence) or the timing diagrams (Figure 71: SPI master transaction) showing precisely...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
In our setup we load merged hex file...
from this link
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader
I gathered that nrfjprog is for flashing...
which is the Example code to test the NFC_Tag future in MDBT42 V P 512K V2 module.
i was using PCA10040 nrf52 development kit in that Example code is working same code not...
I want to disable and enable UART at runtime. I don't use DMA and interrupt.
I read this thread. https://devzone.nordicsemi.com/f/nordic-q-a/52496/nrf9160-uart-pull-up-and...
Hi.
I need to program for a set of NRF52832 with serial number from 403898368 to 403941418.
I am trying with nrfjprog --family NRF52 --memwr 0x10001080 --val %% --verify...
I am in the process of evaluating different BLE solutions for a project. The project consists of a pair of BLE-enabled devices which need to be able to go into dual-role mode...
Hi everyone
I don't really understand what the physical cell ID is. Is it a randomly generated ID created by the nRF9160 chip or a set ID within the cell?
As far as I...
Hello,
I am facing a really annoying issue when updating my SPI settings from the old nrf_drv_ towards the newer one nrfx , in SDK15. I am following the recommendtations...
Project context: -------------------- Server BLE for home trainer diy Target (Bluetooth server) : Bluefruit nRF52 The feather Library : BluefruitBLE Client : nRF Connect ...
Hello,
I am using nRF52840, SDK_16.0.0, S140 SoftDevice and Segger 4.16 for flashing the image. I am using ‘ble_app_blinky’.
1) If I enable “Just works” and without...
I have a project where one device will be both a peripheral and a central. In the central role the device will connect to a sensor. It will act based on the sensor data. In...
