I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
when i try to use the ddfs to calculate the distance, i can't understand the comments in the README file,
"Zero-distance calibration
*************************
The...
I have followed the guide at https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu .
(using the option CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
After the Matter device is upgraded from version 1.1 to 1.3 via OTA, the Thread connection is functioning normally., but it fails to process chip-tool commands, and chip-tool...
I'm interested in connecting a device to a combination of RAK4631 and RAK5802 using RS485 interface.
I write the code in the Zephyr environment and I cant seem to make it...
"I'm trying to perform DFU using MCUBOOT over Bluetooth. The device enters DFU mode and connects successfully, but when I start the firmware download, I get an error:
Starting...
Hello Nordic Team,
I am currently implementing low-level SPI communication using SDK v2.7.0 and nRF 5340dk . Could you please let me know the name of the IRQ handler for...
I have received my NRF52840 DK V3 and i open NRF connect for Desktop and run "Quick Start", it have detect the board but when i try the hello world program test it is not...
Hi Nordic team, We have a project that uses nRF5340 &NCS 2.7.0, and we encountered net core crashing issue each time when ble is connected by central device and 5340 app core...
Description:
Hello,
I am trying to build my project nrf_dm_testing using NCS 2.9.0 , but I am encountering a CMake configuration error. The error message is as follows...
I am using 9160 as slave which communicates with nrf5340(master) over UART. with flow control disabled everything works but as soon as I enable the hardware flow control then...
Hello,
I have a few questions regarding the nPM1300 current measurements:
As far as I understand, there are two ways to trigger a current measurement:
By writing...
I am using VS Code IDE and have installed nrf Connect Extension and done with the installation part and blinky and few other samples. So, basically I just copied an available...
I have figured out a way to realize IR communication,it is same with the way to drive WS2812 with SPI.
[ I can use PWM peripheral and should use it,for I need to change...
Just to confirm the head question.
I have found the same question : NRF52 help configuring TIMER + DMA + PWM - Nordic Q&A - Nordic DevZone - Nordic DevZone
There is no...
