Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am using SDK 3.1.1. I am trying to use the "sensor get" command with the internal die temp sensor.
In theory, this is all off the shelf software. I didn't write anything...
While running scan & connection tests with NCS 3.2.1 , I encountered frequent connection timeouts ( bt_hci_core: Connection creation timeout triggered ) when using the Nordic...
I'm using the Power Profiler Kit II to measure current draw of an ESP32 board at idle. The PPK2 is connected to the battery terminals of the board (XIAO ESP32-S3) and whether...
Hello, I should like to enquire whether the nRF54L15-DK development board supports both Classic Bluetooth and Bluetooth Low Energy. Having reviewed the relevant documentation...
Dear All,
I'm following the nRF Connect SDK Fundamentals and I have a weird problem in the Lesson 3 exercise 2, section "Adding custom configurations".
The part with...
Hello everyone,
I've been testing the "central UART" with a "peripheral UART" (NUS) examples with two nRF54L15 DKs (nRF SDK v3.2.1 in VS Code). So far, everything is working...
Hello everyone!
I have a question regarding nRF9151 and the new DECT Hello sample. I have installed the newest version of the SDK, a preview of v3.3.0, built and flashed...
Hi!
NCS 3.1 On a custom board with nrf5340 and nrf7002, h ave successfully implemented and tested FOTA over Bluetooth Low Energy with Simultaneous updates for both cores...
Hi,
I'm trying to reduce the power consumption of my Matter Temperature sensor code.
I'm averaging around 90µA of consumption, but I'm confident that can be reduced. ...
Hi,
I’m having trouble getting an ISP1807 (nRF52840) to run on a custom PCB, and I’m hoping someone here might recognize what I’m missing.
Hardware / setup
Module...
Hello, we’re currently facing an issue regarding the start-up of the nrf9151 modem. Its a custom PCB and closely follows the schematic of the nrf9151 DK. For first test SW...
Hello Nordic Engineer,
I know that I can modify #define DEVICE_NAME "device001" in sdk_config.h , but it takes a lot of time to compile and flash the program every time...
Hi,
I have flashed hci_usb example on nrf52840dongle(hci1), enabled DLE. But when linux machine requests data from other board(as sender) dongle is getting crashed.
The...
I have create a model (which is now marked as complete), but when I go to the results tab the options (and below) just show a spinning circle. How can this be fixed?
