I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hi
I met a problem when I use my new board,I found that the example in the peripheral folder in SDK can run correctlly,but the the example in the ble_peripheral folder...
Hello Team Nordic, May I ask for your advice on how to build one nRF52840 to have two different UART connections to two different devices? May I ask for the any code examples...
Hi,
I am trying to integrate custom protobufs into the asset tracker project. I am referencing the zephyr/samples/modules/nanopb project for the same.
But I am getting...
HI ,
I'm trying to open terminal/command SDK v2.0.0 from toolchain manager (working with nrf connect for desktop v3.11.1) but it doesn't open.
while on SDK v1.9...
I'm just trying to make a simple communicatión between my nrf52 dk and my mobil using Serial Bluetooth Terminal app. I took the ble_app_uart example and I added a function...
Hi,
My project is a host micro (STM32) and a nRF52840 (controller mode) to implement a peripheral. My previous project (STM32 BLUENRG-M0 and host micro, HCI SPI interface...
Hi,
I'd like to add live audio streaming to my product, The current product consists of a sender unit and a receiver unit. Both using the nrf52833 (I've already bought 500...
hey guys i want to implement two separate application programs on the same chip.
Say Application1 is stored in address start_address1 to end_address2 and Application2 is...
Before using J-Link script to upgrade firmware, offsetStart (0x0) and offsetEnd (0x32E06) are correct. But after using J-Link script to upgrade firmware, offsetStart (0xADDEFE01...
Board: nRF52810
SoftDevice: s112
SDK version: 17.0.2
I'm trying to enable 2Mbps data rate. So I've added The following code in both peripheral and central.
ble_gap_phys_t...
I try to create new application using worspace type but fail , if I use freestanding type is OK. I already downlad and install SDK 2.0 . What happen? Could someone help me...
Hello, I just wanted to throw in that for a hobby project I created a PWM audio driver, with which one can play back 8-bit audio data very easily. Since it may be useful for...
hi
i'm new to the nRF platform and realised it uses zephyr. i come from a pic & stm32 background with little rtos knowledge and find the official zephyr cryptic. especially...
I created a BLE device with custom characteristic showing the sensor value (int16). But I can't achieve 1khz sampling rate.
1. Is sending data via NUS faster since the central...
I would like to using Keil to build secure_bootloader project for changing NRF_DFU_BLE_REQUIRES_BONDS from 0 to 1. But Keil failed to build. Please refer to snapshot of Keil...
