Hi,
I am trying to use the PORT event to trigger interrupts when a button is toggled, i.e. both on LoToHi and HiToLo.
To my understanding PORT events are generated by...
I am running Windows 7 Pro SP 1 64 bit and have gong through the tools installation procedure, in particular running nRFTools_7_7_0_Installer.exe. This ran the J-Link V5.02...
I am very familiar with the arduino side but the BLE is brand new to me. I was wondering if I can use P0.00 and P0.01 to talk to the arduino and if its possible how exactly...
Debug Logger without softdevice, and the define ENABLE_DEBUG_LOG_SUPPORT to my project in the C/C++ tab.
i just test, very simple , but cannot get debug log..
int main...
I am trying to use the scheduler, but I would like to know if it is possible to have events with different priorities... As an example:
Task A - Priority LOW
Task B -...
FIXED (see below)
Hi!
I'm developing software for nRF52 on nRF52 preview DK, which I got on the Global Tech Tour.
LED blinking (blinky) example is running OK, so I moved...
I would like to test GPIOE APIs on nRF5340 develop board. But west build generated the following warning message.
Could I use nrfx_gpiote _xxx related APIs ( infocenter...
Hi,
I am not sure how to read from a characteristic which doesnt have notify property in them. I started looking into nrf_ble_gq_item_add() But I am not sure on what parameters...
hi
I am trying to get the nrf7002 dk working, however, when i try to provision the kit using the nrf wifi provisioner app i get an error saying " scanning error received...
Hello,
I'm working on nrf5340 audio bis gateway sample.
The NCS version I use is v2.2.0, I know it's a very old version, but for some reason I can't update to the latest...
| Host | <---- UART ----> | nRF52833 (central) | <-- BLE--> | nRF52833 (Target) |
I have a requirement where I hope to update the central's firmware image through the Host...
Hello,
With the latest version of the nRF5340 MDK I am getting the following linker errors (below), and don't understand why they should turning up.
Best regards
==...
Hello,
The documentation in the nRF7002 Product Specification rev 1.0 says that the P2P mode (Peer-to-peer) is supported (section 6). However in this ticket: https://devzone...
I need to use ADC in the project, and then I have configured ADC in overlay. The code is as follows
The same code can be measured normally in Zephyr's ADC example, but...
Hi,
I'm trying to use an nRF52840 dev kit as an I2S-to-USB microphone, but I've been running into a problem where the recorded audio is periodically unusable.
To debug...
Hey Everyone ... Looking for some ideas / help with crash involving nRF Sniffer v2 and Wireshark. Specifically I have an older White MacBook that I use for sniffing and nRF...
Hi,
I am using sdk 16.0 and I am already using 3 SPI Instances i.e. SPI1, SPI2, SPI3. I wanted to use SPI0 Instance also. How to use it?
If enable SPI0 in sdk_config I...
Hello
I was working on nrf9160-dk with assert_trakker_v2 application successfully connecting to nrf Cloud. There was no problem.
Today I started the day by deleting it...
From what I understand, the nPM1100 can work without the battery (i.e. no BAT connection).
Does the Nordic Thingy:53 come with the Li-Po battery separated or is it mounted...
Good afternoon everyone, how are you?
I'm using custom hardware, Nrf52833+Nrf21540, already reviewed by and tuned by Nordic. We are going to carry out the tests for product...
I need to work on single bank DFU from esp32 to nrf52833. I found a website with instructions on single bank configuration here: academy.nordicsemi.com/.../topic /exercise...