Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
Hi,
I have a question after using the DMIC example on the nRF5340:
how do I adjust the PDM clock frequency to 1.28MHz, or how can I achieve this by changing the value...
hello Nordic
i am working with nrf 52840 and 52832. using ncs v2.8.0
i am saving a coredump to flash partition and i am using gdb server - client to try to parse the coredump...
Hello,
I'm migrating an ANT+ BPWR application from **nRF5 SDK** to **NCS v2.5.1** but cannot install the sdk-ant module.
**Background:** - Previously used nRF5 SDK with...
Hello,
I send a ticket because I have an issue to access and write files to a SD Card with NRF54L15DK and 3.1.0 SDK and toolchain.
Can you help me please ?
Here is my...
Hello,
we are trying to run Gazell samples on the nRF54L15-DK, but the protocol & board combination doesn't seem to be supported by version 3.2 of the nrf Connect SDK...
We would like to synchronize several Nordic thingys 53. The Approach is to send two timestamps from a central to them (peripheral) via Bluetooth Low Energy with 100 ms delay...
Hi
I try to start with ST7789 display on nRF54L15 and there are bus fault after add LVGL library. The project is building correctly, but stop just after leave bootloader...
Hi,
I accidentally opened and subsequently programmed the PPK-II in Bluetooth Low Energy module startup. The programming didn't complete but resulted in an error. Now...
We are using the nRF9151 with modem firmware v2.0.4 and would like to perform TX RF testing on NTN bands 255 and 256.
TX RF testing is currently initiated using the modem...
I am working on a project where we are sending data to a remote device as fast as possible. The sender will call bt_gatt_write() until it blocks the thread. So it is just...
Dear Sir/Madam ,
I am writing to request a review of the attached schematic. Please let me know if you have any questions, concerns, or suggested revisions.
If possible...
I am in process up migrating a legacy project from SDK v2.4 to v3.2 and going through each revision incrementally to catch all the changes needed to modernize it and maintain...
I have built and flashed both the exercise and the solution. However in both cases I am getting a connected and then disconnected ( Reason 42). I am clueless as to what is...
Hello.
I am currently testing nRF Cloud and encountering an issue. In the "Select a Project" menu, the "Create Project" button is disabled.
Here is some additional context...
