Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
I'm attempting to troubleshoot a system crash when polling a sensor at higher ODRs while BLE is enabled. I'm using NCS v2.9.0 with the nRF54L15. I checked the thread stack...
I'm trying to compile the lsm6dso example for a nrf5340. I also tried the nrf52832, but I get the same error.
v2.4.2\zephyr\samples\sensor\lsm6dso
prj.conf:
CONFIG_STDOUT_CONSOLE...
Hello, i'm considering an application using nRF52840 in following configuration:
- I2S RX would be connected to some external I2S source (I2S slave)
- I2S TX would be...
Hello, I'm trying to make a application bootable through MCUBoot but I'm having a hard time generating the .bin file with MCUBoot header. According to this page I should be...
Hi I want to use nrfutil nrf5sdk-tools in MacOS but when I try to run it I get the following error.
" Error: Failed to spawn inner nrfutil-legacy executable
Caused by...
We are trying to update the SDK used by a firmware on a device that is in production. The old SDK is 2.1.0 and we are trying to update to 2.9.0.
I was able to get the firmware...
i am currently using nrf52840 dk as a hardware, nrf5sdk version 17.1.0 ,ble_app_uart peripheral example (s140 soft device )
here the maxmimum mtu is set to 247 bytes whether...
Hi everyone, When I try configure UART (parity, data_bit, stop_bit, flow_ctrl), I have noticed error when I run in terminal: "
*** Booting nRF Connect SDK v2.9.0-7787b2649840...
Hello
I am developing an application based on the nRF9160, it uses Coap protocol to connect to nRFCloud to transfer the data. Also I have implemented the FOTA which always...
Hello,
I am using the nRF52810 with SoftDevice S112_nrf52_7.0.1 and trying to create a simple program that sends the character "1" to a mobile device. However, I am encountering...
I've been having trouble downloading the Connect SDK in VSCode, so I want to download the SDK from GitHub first and then import it into VSCode. How can I import the SDK I...
Hi all ! I'm new to the nRF MCU, I'm aiming to use one for a school project.
I've bought the devboard (nRF5340-DK) on a known website (Distrelec.fr, part of RS groupe)....
Hi im having problems with restarting advertising after disconnect. I tried NUS example, simple peripheral example but none of them works.
I modified NUS example with some...
NCS 2.9.0
Adding mcuboot to sysbuild and using "sysbuild/mcuboot.conf" works as described in Academy exercise-1-configuring-extra-image .
But if I want to use a board...
I am working on the ZigBee communication my device is working fine but i got in to the issue when i tried to use custom cluster all the resources, i found online are more...
