In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Hi
As described in this white paper: https://infocenter.nordicsemi.com/pdf/nwp_036.pdf during the reference period of CTE signals, 8 samples are taken. These samples contain...
I’m using the DECT Shell perf command to evaluate DECT NR+ performance.
Could you please clarify the units and scaling of the snr field in nrf_modem_dect_phy_rx_pcc_status...
Hi,
What file or files should contain CONFIG_GPIO=y for a simple application developed with nRF Connect SDK v2.9.0 such that VS Code does not show squiggles under #include...
Is there any point to using deferred logging with the RTT backend?
The way I understand RTT is that it writes the message to a buffer where it is fetched via DAP, skipping...
Hello,
I'm trying to implement runtime power management (SDK 2.9.0), but as soon as I enable the option, the shell and logging on UART0 stop working at startup. The rest...
Today I bought a new NRF-PPK2, but compare with my old NRF-PPK2.
For the old and new PPK2, I use the same DUT.
It can't show the same current with my old one? can you...
Hi,
In our project, we are planning to use the nRF9160 for both LTE-M and Wi-Fi. Thus, we have connected the nRF9160-DK to the nRF7002-EK in the developing phase as we read...
Greetings developers,
I am using nrf connect sdk 2.7.0 with nrf52811 soc. 1) present situation:
My application sequential in nature and does not have multiple thread...
Hi,
I am failing to build any of the Matter, Thread or Zigbee for nrf52840dk with the following failure.
I successfully build a blinky and bluetooth app, so my tool chain...
I am trying to use fstorage with the sd backend (SDK 14.0.0). My issue is that, after successfully calling nrf_fstorage_write, the callback I registered using
just never...
Hello,
I'm developing a program on a NRF52840 DK in the SEGGER Embedded Studio IDE that outputs a PWM signal when a Bluetooth Mesh GenericOnOff signal is recieved.
I got...
Anyone knows why I'm getting this result? I'm building the application using sysbuild and flashing normally on nrf52840dk. I tried both following all the steps in the lesson...
Hi,
i am trying to create an Indoor Positioning System with the nRF54L15.
Currently i am able to connect 1 initiator to multiple reflectors simultaneously,
When...
i have used same Serial_lte_modem sample code from nordic toolchain 2.6.0 , Enabled shell just by setting config macro
CONFIG_SHELL=y and SLM uart loging is by default...
Hello,
I'm trying to run the NVS example on the NRF9160DK rev 1.1.3 with the on-board MX25R6435F external flash memory.
The sample runs OK as nrf9160dk/nrf9160 but the...