Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hi,
I have a device in the central role that connects to a device with a specific name. I then do a db_discovery_start to get the handles of two of the characteristics...
Hello,
I'm trying DFU/bootloader.
Using nus service
Switch to dfu when necessary
At this time, watchdog (2 Sec) enable state does not execute the bootloader...
Hi,
I am mobile developer and very new to mcu programming. Due to our new product's requirements, I have to write program with new bluetooth chip. So if nrf51 and nrf52 series...
To find a clean channel for 2.4g Band to avoid the wifi channel, nRF24L01p would sweep frequency for all the channel (2400M~2525M). But looks like nRF24L01p not support to...
Hello guys!
I'm trying to port the TSS service to one of my projects.
This project is based on SDK13.1 while the Thingy is on SDK12.1
I have a lot of problems with...
Hello guys!
I'm trying to get softblinking led work with a SDK14.
The code works perfectly fine in one of my projects that use scheduler and SDK13.
But in SDK14, (only...
Hi, I think the idea of limiting the behavior of a model to states is very wise, but due to my limited understanding in this matter, I find it puzzling as to what happens...
Is it possible to use the NRF52832 UART in half-duplex single-wire mode, by assigning TXD and RXD to the same GPIO, setting the GPIO drive to disconnect '1' and using a pull...
I am running the example under peripheral\pwm_driver on PCA10040, and SDK 12.2.0. Using a scope, I measured the period (from rising edge to rising edge) on one of the LEDs...
In my project, the softdevice I used was S110
I hope that some of the data can still be retained after OTA updates,
in the Bootloader program code:
#define DFU_APP_DATA_RESERVED...
Hey togehter,
has anyone succeeded setting up a connection between ST-Link and nRF52832?
I connected the pins (GND, SWDIO, SWCLK and second try with GND, SWDIO, SWCLK...
Hi,
Please let me what is the beacon layout of nRF58122 for scanning beacons in region by using following method:
BeaconManager.getBeaconParsers().add(new BeaconParser...
I'm using and NRF52 with S132 and SDK13.0. I'm using Keil as my IDE.
My application acts as a central for smart phones to connect to and also acts as a peripheral to conect...
Hi, I'm a mechanical engineer, an industrial engineer and have a master's degree in control of the dynamics systems. I never get the change to work with ARM architecture before...
Help, what UART output pins that gather all information from the various sensors in the NRF52832 thingy52, to integrate with Raspberry or Arduino, thank you
