Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
I have found that in Linux, "nrfutil toolchain-manager launch --shell" is starting a process that uses almost 20% of the CPU according to the top utility. I have found this...
I'm trying to make a BLE beacon with Li-Ion battery and Qi wireless charging circuit. NRF52833 works in high-voltage mode (VDDH connected directly to the battery, internal...
nRF connect SDK 2.7.0 CONFIG_CHIP_LAST_FABRIC_REMOVED_ERASE_AND_REBOOT KConfig option is not working, it is not erasing nvs and not rebooting device. Although I have enabled...
Hallo,
I'm using Segger Embedded Studio to program nRF52840. In the Nordic nRF5_SDK there is the ble_app_uart example using S140 softdevice, which is running well. Now I...
I am trying to measure the current consumption on nRF52832 PCA 10040 2.0.0 with PPK 2 (PCA 63100 1.0.1).
I have cut the SB9 and connect the PPK as the picture:
as shown...
Im a bit stuck here.
I have the following code, trying to communicate with a flash memory:
Overlay:
code:
I get the following error message:
error: ...
Dear Nordic, I have developed an application for nRF52811 on nRF52840-DK.
For this i have referred examples -> peripheral -> template_project.
I have followed https...
I just fired up our most recent custom boards with nRF9161-LACA's, and tried to compile modem shell application for RTT.
I noticed the RTT is disabled because HAS_SEGGER_RTT...
I am working nrf52840 with bg96 modem, i have configured quectel_bg9x.c driver to communicate with bg96 modem from nrf52840.
can you provide a sample application on MQTT...
Hello,
I'm experiencing an issue integrating a freestanding Zephyr module with the sysbuild system. The module defines custom boards and projects. When I use the...
Hi
We are the Manufacturer of Smart lighting
We have start new project" Cellular gateway".
We are evaluating the nRF9160 Dk board .
During this we found issue . it...
Hello,
I have 4 nrf52840, 3 act as peripheral and the last is the central.
The peripherals are identical hardware with various sensors using the same FW. I order to...
SUMMARY
Attempting to OTA the nrf52840dk over BLE.
I was able to perform most of the steps in this sample: https://docs.nordicsemi.com/bundle/ncs-2.1.4/page/zephyr/samples...
I have a photodiode, and under indoor lighting conditions, the reading on the oscilloscope is about 150mV. When I connect it to an Arduino Uno or Adafruit nRF52840 Sense,...
I built an application on the NRF52 Development Kit.
I was using the old NRF serial application with the retargetio.c file to push data out through the serial port.
I...
