Hi there is a problem in github.com/.../nrf51-UART-examples
any one can help?
I put empty loop in main, and comment off all ble related int. and I process uart_evt by...
Hi,everybody！
When i install master control panel 3.10.0.14, i can't find nrf.exe in " C:\Program Files\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf ". Only nrfutil...
Hi,
I've been using the nRF51 dev kit, and today it stopped mounting when I plug it in. It doesn't show up as MBED or BOOTLOADER.
I use both Mac OS X and Windows, though...
SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi all!
SPI3 Slave project is not built - error:
identifier "__device_dts_ord_DT_N_S_soc_S_peripheral_50000000_S_spi_c000_P_cs_gpios_IDX_0_PH_ORD" not determined
C:\ncs...
Hi,
I want to measure CO2 in different locations using two similar CO2 sensor ( MiCS-VZ-89TE). I can communicate with the sensor over I2C0.
But because two sensors have...
We are facing an issue in nrf52840 (SDK 15). Our hardware uses timer, SPI, USB, FLASH and uDMA. implemented watchdog timer and its working fine as well intented. But in some...
Hi I hope you can help me with this.
I'm using a nrf52833. When I build I see Flash usage of 278044 B.
Regions Size 512KB.
My custom board has this in the Flash0 settion...
Hi DevZone, I am using the nRF52840 to interface an ADS1298 (ECG Chip) via SPI.
I want to test if the communication between the devices are working by:
- Sending a RREG...
Hi All,
How do I disable the BLE stack completely such that I can switch to the DTM stack (DTM example using direct nrf_radio calls)?
Current I disable advertising and...
I want implement beacon function on my Qualcomm BSP board.
However, I'm testing with nRF52 DK in advance.
And need DFU OTA update for my F/W application.
So I'm implementing...
I am trying to configure the nrf5340 audio example to add the ability to update the firmware using a serial connection.
In the audio example documentation, there are a few...
Hi everyone,
I called "bt_gatt_notify()" from workqueue. Usually there is no problem, but when move far away, "bt_gatt_notify()" doesn't return. I called "bt_gatt_notify...
Hi, I'm currently using the Direction Finding Connectionless examples to evaluate using the nRF5340 for numerous projects we have lined up, and I'm having difficulty ascertaining...
Question: Based on the chip nrf52840, I want to design a product application that can work with matter and thread at the same time. Is it possible to implement this design...
Hi dear team, Im currently on the NRF9160 DK (0.9.0) trying to get SPI up and running.
nRF connect SDK v 2.1.1 using visual studio code. However Im having problems getting...
Are the memory-mapped hardware addresses (e.g. 0x40000000 and following)
on the nRF52840 mpu restricted from access by the Zephyr RTOS.
If so, can this be defeated ?
Hi, I'm using NCS v1.9.1, and attempting to upgrade MCUBoot via DFU over BLE using the nRF Connect for Mobile app.
I'm able to successfully DFU the application image. However...
