SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
Excuse me:
I can't find a api to close WDT，When the chip enters idle mode, the watchdog will reset the chip，I tried to call the command in the diagram below to turn off...
Hello,
I'm using nRF52832 board and I want to use it as a controller with a third party cellular modem to connect to AWS IoT. i.e. I want to send AT commands with the UART...
Hi,
I am trying to minimize the power consumption on a NRF52840.
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/optimizing-power-on-nrf52-designs states...
nRF52840 can support matter (BLE + Thread).
it is noted at https://github.com/project-chip/connectedhomeip/tree/master/examples/lock-app/nrfconnect
even that have a demo...
Excuse me：
How to get profile QDID，host QDID and controller QDID of nrf52832？The current SDK version is nRF5_SDK_15.2.0_9412b96,Soft device is S112,thank you!
My goal is simple. I want my nrf5340DK to communicate with my nrf24L01+ Just to test the water and also because I have experience working with the nrf24 modules. Is there...
[ Problem ]. When communicating with the TestApp as shown below, it is taking an unusually long time to get a response. The problem is that the response takes more than 0...
Hello,
I’m currently trying to flash the blinky code (found in the ‘Getting Started’ section) onto the nordic nrf9160-dk.
The error I’m getting is :
“error: cmake...
Hello,
We have a development team in Kiev, Ukraine.
We see that LTE over nRF9160 is not working there.
Is it possible that LTE over nRF9160 is not supported in Ukraine...
Hello
We are using secure boot loader for DFU and is working great. We were using single bank DFU, but reduced our image size to allow dual-bank DFU. If you could please...
Hello Nordic Devzone Community,
I am developing an out of tree driver for firmware running on an nRF9160. I've made some progress and am getting closer to correctly implementing...
Dear Sir/Madam,
We are trying to lower the low frequency crystal start-up time.
https://infocenter.nordicsemi.com/topic/ps_nrf52840/clock.html?cp=4_0_0_4_3
In the description...
I'm wrapping up a job for a client and we are squashing the last few bugs, but I can't seem to understand one of them. Pin 0.13 of our nRF52840 is pretty simple, just a button...
Looking for wisdom on wiring up the nRF (52833, via Raytac RF module). I'm having a hard time understanding (PS, Hardware Layout) section how the different power Configurations...
Hello,
I have previously created a product using the nRF8001 chip a year ago using a PCB antenna design. At the time the enclosure for the PCB was RF transparent and the...
