Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Hi,
I am using "otCoapSendRequest" to send data to my coap server.
Inside the callback, I am using otMessageRead, to read the response.
But my code crashed inside otMessageRead...
Hello.
I am developing using nrf52832 (S132 v7.0.1, SDK v17.0.0) as a peripheral device.
The question is, is it possible to GATT communicate with each of the multiple...
HI
I am traying to convert library max30105 arduito to Nrf52840 code but i have a problem about this
I am reading de Reg FIFO led red and led IR , but its not the same...
Hi I'm currently using the sample py script which is given in https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/nordic-thingy52-raspberry-pi-python-interface...
Hello Nordic Team!
I'm working with the nRF52832 and following this tutorial from Nordic to do OTA DFU: https://devzone.nordicsemi.com/guides/short-range-guides/b/software...
OpenThread and MCUBoot don't play well together anymore of the nRF5340 with the release 1.8 of the nRF Connect SDK. Flashing :
results in the bootloop with I assume is...
Hello,
I am a beginner in nRF. I want to implement EEPROM. So I am trying to execute Zephyr/sample/driver/EEPROM code but I am getting compilation error the below error...
Hello,
I am new to BLE. I am currently working on a beacon application. I have used the beacon example code from SDK and modified it. I am using SDK-17.1.0 controller is...
SDK: 15.3.0 SoftDevice: S132 Device: EYSHJNZWZ (nRF52832)
Is it possible to simultaneously send advertisements with different cycles, communication packets, etc.? If so...
I've been tinkering with my Dev Kits (3 @ nrf52840-dk and 1 @ nrf5340-dk) as I try to find the right software/hardware architecture for my use case.
I made a lot of progress...
Hello , i am developing drivers for a spi ic , which by using spi example i wrote the drivers they are working fine , also i am able to run and modify ble uart example according...
Hello Sirs
I am using the NRF3540-DK development board to program an external NRF5340 chip. I have connected the RESET,SWDCLK,SWDIO,GND,3V pins of P20 connector on development...
I need to connect a ble device to a double uart0 and Uart1 over zephyr.
The first uart in used for comunication puupose e message everty 20mS at 115200;
The second uart...
I'm trying meshdfu. Use 52832 to DFU a lantern program according to the official routine. After success, the program can run, but it can't run after DFU with 52840. Here's...
Hi,
I'm trying to build the blinky example for the nRF5340 network processor with the empty_app_core as a child image for the application processor and get a fatal error...
