Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
tl;dr: The clone would probably work more reliably if the nrf-toolchain-manager added the --depth 1 option, e.g.: git clone --branch v2.6.1 https://github.com/nrfconnect/sdk...
Dear
I'm working on controlling an I2C device.
I want to achieve TX->TX using the nrfx_twim driver. I specified NRFX_TWIM_XFER_TXTX. When I looked at the nrfx_twim source...
Hello,
During design and schematic entry I used the online datasheet to select GPIO capability. I was advised that I should try out the pin planner to confirm that pin choices...
I am using the nrf_fuel_gauge_idle_set function to handle the fuel gauge state when the system enters a low-power mode. When the charger is connected, I exit this state and...
Hello Nordic Support Team, I am experiencing an issue when using MQTT over an NB-IoT connection with the nRF9151 DK, and I would like to ask for clarification and guidance...
Hi,
I am working on a Matter device based on Nordic NCS v2.9.0, using Google Home as the OTA provider.
I have successfully uploaded a new OTA image in Google Console,...
n the nRF52805, if the hardware is configured for DC/DC regulator operation—namely, with the DCC and DEC4 pins connected through the designated inductor and capacitors—does...
I am using a Thingy91x, with some additional sensors attached via qwiic cable.
Initially to test the Thingy91x I inserted the SIM and scanned the QR code on the Thingy91x...
I am developing a proof-of-concept for remote controlled super-low-power devices using PAwR. I started with nRF52840 (for boths, clients and remote) and now migrated my code...
I built and ran the Matter Light Bulb example for Thread and was able to commission it into Home Assistant with no issues. However, when I tired the Matter Temperature Sensor...
Hi
Setup: nPM1300, nRF54L15-based board, SDK 2.9.2
I am trying to figure out how to use the nPM1300.
So far, I have not succeeded. Quite frequently, after power...
Hi,
I downloaded the NCS v3.2.0, but always got the error below when u npacking the toolchain , the same error when downloading via Vscode. and there is no problem for v3...
Hello all, I am using the nRF52840 together with the nRF7000. To save GPIOs, I would like to use the BUCKEN pin (which is directly connected to the nRF7000) also as the enable...
I tried to compile the project according to the link（ https://github.com/nordicsemi-neuton/nrf-edgeai-thingy53-ble-remotecontrol ）, but the compilation failed.
The compilation...
