In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
We are testing SPI communication with the nrf5340 Board as the mater and the nrf52840 board as the slave.
The FW applied to nrf5340 is a FW whose normal operation was confirmed...
I have a problem understanding notifications/subscriptions in the BLE context.
I have two devices, Central (nRF5340) and Peripheral (nRF52832). My peripheral provides a...
This not a question. It is for your information (FYI). I've seen many questions about flashing the nRF53 using CMSIS-DAP. Anyone interested see attached instructions.
The...
Using an approach similar to what's in the ble_app_att_mtu_throughput example, my goal is to transfer data as fast as possible. (I.e. call sd_ble_gatts_hvx() on the same characteristic...
I'm building the nrf/samples/openthread/cli sample with the nrf54l15dk/nrf54l15/cpuapp/ns board. The only change I'm making is enabling CONFIG_DEBUG_THREAD_INFO.
The app...
Hello,
I am using an LE audio code "nrf5340_audio" code from nRF SDK v2.8.0 to play a beep tone. I want to play a tone from a temporary memory, so I have created a logic...
I'm following the dev academy lessons and I'm having a bit of an issue where VS Code intellisense isn't picking up on the include paths from zephyr (e.g. #include <zephyr...
Hi, while working with the nRF9160DK i get this Error a lot of times, I can't say "Yes" or something else and have to wait until the progress bar fills completely. Even if...
Hello
Our 52840-based device has a functionality of playing one of 10 pre-recorded phrases via I2S interface. We'd like to be able to update the wording or load a different...
When integrating DTM into my main app, I have to comment out the macro CONFIG_BT=y to ensure the DTM test can run properly after the build. Are there alternative ways to include...
Hi
I am working on nRF54L15-DK (PCA10156 0.9.2 2024.49) with chip N54L15 QFAAB0 2444AA
I am using Nordic SDK 3.0.2 and Zephyr 4.0.99
My task is to have the top 2K of...
Trying to read button 3 on the npm1300-ek, which is gpio 1 according to the schematic. The following #defines represent the gpio related registers on the npm1300:
#define...
I have been using my nRF54L15-DK board since it arrived just fine, however today when I went to flash the firmware I received the following error:
-- west flash: using runner...
Dear All, I am looking to connect to WiFi enterprise AP. So far I have been able to connect to the network using the nrf/samples/wifi/shell using a command that looks like...
