How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Dear all:
I used this command to build light switch for 5340DK:
west build -p always --build-dir nrf/samples/matter/light_switch/build -b nrf5340dk_nrf5340_cpuapp nrf...
Kconfig failed: [Errno 22] Invalid argument: 'c:/users/user/zephyr/kconfig"' is an error that appeared this morning. What is supposed to be in the Kconfig file. I have been...
I can't remember where I found it now, there was a file somewhere that listed all the files in a project. It had
absolute paths which filled me with dread as it means a...
Hi
I am working on a custom board and have hit an issue with the software part. When the nrf_modem_lib_init function is invoked, it always ends with a timeout (errno ...
Got a Thingy91 (not the x model) that doesn't show up as anything when connected to a PC by USB, except when in bootloader mode, by pressing SW4 (no reaction with SW3) when...
I read other similar issues on this forum but they haven't helped solve my problem. I started with the peripheral_uart example project. Development and execution on the target...
Sorry for long sentence. The nRF5340 document describes about the Reset. This chip set have the POR. so, if POR function work, I don't need to use the PIN reset. because POR...
I have configured my application according to the Throughput example. The prj.conf file inside the sysbuild\ipc_radio folder is not being considered in the build. As a result...
Hello, everyone.
I would like to use mcumgr to update the firmware of a nrf52 via another nrf52 over uart.
From the documentation I understand that smp supports uart so...
Hello,
I just got started with the nRF5340 DK. I went through the example which instructs how to load the "Blinky" applications, build it, and then flash it to the Board...
Hi! I am trying to get OSDP communication up and running on my nrf9160dk board. I am trying to run this sample: https://github.com/zephyrproject-rtos/zephyr/tree/main/samples...
Hello,
I apologize if this is a simple question. I am working with the nRF9161-DK and am using the Serial LTE Modem application. The ultimate goal is to send data via...
I'm working on a Matter 1.3-compatible door lock with RFID credential management. I’ve enabled RFID support through the ZAP tool and configured the feature map accordingly...
Hi,
I am using the NCS Thread CLI sample as the base of my project and I was wondering if it's possible to disable the cli command functionalities of this project to save...
Hello,
I would like to keep track of time in Nordic Connect SDK (v1.9.1) based application.
The application has both BLE and Openthread enabled.
Before using Openthread...
