Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
We have created a zigbee custom sleepy end device with the base from light switch example. We are able to perform most of the operations successfully.
We have set the following...
in main.c, you have this code
but if you set CONFIG_BT_NUS_SECURITY_ENABLED=n in the prj.conf file, then there are #defines that will prevent the definition of the...
There are two DKs, one works as a slave while the other works as a master. When these two peripherals are connected via Bluetooth, they exchange each other's parameters via...
Dear Support Team
Our customer prepared to develop a triple mode operation game keyboard which communicating over Bluetooth LE, either via the dongle or USB. Should the...
Hello, thank you for taking the time to read this.
I've been reading through some of the forms, and I'd highly appreciate someone with more experience giving me some input...
Hi Support Team,
I’m designing a custom PCB using the nRF52840 based on "Circuit configuration no. 6" from the nRF52840_PS_v1.0.pdf. On our design, VDD_nRF = 1.8V which...
Hello,
I'm making some sensors based on nRF52832 and I'm using them as native transceivers. Maybe I'll look at BLE Mesh in the future but at the moment I just send and receive...
SDK 17.1.0
I developed a firmware that can be used in nrf52833-CJAA-R, but it can't be used in the nrf52833-CJAA-B.
According to the following link:
devzone.nordicsemi...
Hi Nordicsemi Team,
The one of our customers recently purchased NRF52-DK (Dev. Kit) which was Ver 2.1.0.
But This time has issue. He thinks after version 3.0.0. cause...
Hi, I am currently trying to use PWM on nrf9160 DK to control a stepper motor. Do you have any sample code for PWM? Also do you have the pin assignment of which pin on the...
Hello! I am working on a project I have set " sensor/server" as my starting point. The sensor is successfully interfaced with NRF52 I need to store the calibrated data of...
We're trying to develop a device driver by putting it in our application folder (under /drivers).
The west build system now recognises and builds it through the Kconfig...
I am following the instructions to set up NUS shell through bluetooth with the following example: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth...
hello
I try to make work the ADC on the NRF52840DK
I would like to use any of the 6 channels on the ARDUINO connector (p0.3, p0.4, p0.28-p0.31)
I am simply not able...
Hi . We have been struggling for months now to achieve DFU updates for our firmware with no success. On our latest stage we get "Can't find room for update". We are just trying...
