Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
I have to use 240 bytes for my sensor value to send in bluetooth. so i choosed to work on ble_app_att_mtu_throughput i need only pheripheral to work on it . i have to remove...
Hi, I was wondering if hosting more than one nrf Connect for desktop version on the same computer was possible. The reason is that I need to use both the old app LTE link...
Hello,
I have connected a LSM6DSO sensor to my nRF52805 which is powered via GPIO. At startup zephyr RTOS wants to init the sensor and failed. After a reboot it detects...
On the SDK 17.0 NRF52840 platform, using sd_temp_get to read the chip temperature works correctly. However, if the sd_clock_hfclk_request function is used in subsequent operations...
Hello,
I'm trying out the example code "pin_change_int_pca10056". But the delay time between sensing a voltage change and toggling the output GPIO is quite long. 22us. Is...
I wanted to know in what ways can I connect thingy:53 to nrf9160 dk via Bluetooth? I understand that dk has onboard nrf52 and hence thingy:52 could get connected wirelessly...
Hi all, I am using the nRF52840 and I came across the nrf52_handle_approtect() func in modules/hal/noridc/nrfx/mdk/system_nrf52.c.
In the nrf52_configuration_249() function...
Hi,
I am unable to access P0.09 and P0.10. I face a similar problem to this thread . I've declared CONFIG_NFCT_PINS_AS_GPIOS=y in prj.conf. Also I've checked 0x1000120C...
i have a custom board that uses a nrf5340 that has been hardware modified so i can work again on getting my board to draw the mimimum power from the battery.
i have a PPK2...
I am using nRF5 SDK (17.1.0).
The MTU size is set to 53. I am using sd_ble_gatts_hvx() to send 16 bytes of data via Notification.
When I check the received data with the...
Hi,
Our product is currently undergoing FCC and ISED certification with Dekra. They are asking for 58741REM.001, 59675REM.001 and 64610REM.003A1 reports for reference. Can...
Hello! I am a newcomer to nrf and embedded programming (other than basic arduino and micropython projects). So far I have gone through many of the devacademy walkthroughs...
Hi, I'm trying to read data from an LIS2DH accelerometer using the nRF5340 DK board. I have been able to build and flash my code to the board, but the terminal outputs, "Device...
