Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am using nRF52833 PCA10100 board. While trying to run sample ble code in segger embedded studio, I am frequently facing this error which says, .text file is larger than...
I am setting up Segger Embedded Studio on my M2 Macbook and running in issues.
I downloaded S140 (nRF5_SDK_17.1.0_ddde560) and upon the build, I see the following errors...
I have a nrf9160dk that drives a screen via SPI, using an IT8951 controller. The firmware driving the screen works fine if I plug the USB cable on a power bank or using MS...
Hi, I'm getting an error when building the example program blinky that says: ".text is larger than specified size" and ".rodata is larger than specified size".
I'm using...
I'm following the steps in exercise 1 of the nRF Connect SDK Fundamentals and getting configuration failures. From what I can tell it looks like Zephyr is failing to build...
nRF Connect SDK v3.2.0
Write code:
Read code:
Log:
The address seen on the phone is usually not "06 05 04 03 02 01", but sometimes it is "06 05 04 03 02...
After the PPK II had been stored for a long period of time, it was recently taken out to measure current. It was observed that, regardless of whether Source Meter mode or...
Hi all,
I have been attempting to get the nRF Connect VS Code extension setup to try out some samples on the nRF9161-DK board.
I'm currently having a problem with a version...
Clarify the minimum mandatory external connections and pin/rail requirements for an nRF9151 to boot and run a flashed application, and determine why serial_lte_modem (SLM...
Hi,
I'm working on an application that I recently updated to ncs v3.1.0 (from v2.9.1). For most of the development, I have been working with the nrf54l15 as build target...
HI
I have replaced the external flash used with the nRF54L15 with a different model. How should I set the sfdp-bfp parameters for this new flash?
Thanks!
Using nRF5340-DK, nRF Connect for VS Code 2026.1, ncs v3.1.1 I'm interfacing over a SPI bus to a custom ASIC that uses MISO as a sort of RTS/CTS kind of idea. While CS is...
Hello,
I'm experiencing an issue where RTT logs stop appearing after MCUboot jumps to the application on nRF52832. The application is running correctly (BLE advertising...
I Just got nRF9151 SMA board, try to test NTN feature , after following instruction to update so called "alpha" firmware, somehow the board can not reflash back to any vesion...
