Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
I'd like to use the GATT/GAP driver from an ARM based Linux system. Is there any possibility of getting a library compiled for ARM or (cough) the source code to build it myself...
Hi,
I am evaluating the nRF5340 Audio DK and measuring while adjusting the audio bitrate.
I found the following 3 symbols definition for bitrate.
CONFIG_LC3_BITRATE...
Hello
I got a nRF52840 DK and try to use Direct Test Mode APP (v2.0.3) in the nRF Connect for Desktop (v3.12.0).
However, it always says "Can not communicate with device...
I have sdk 2.1.0 and nrf5340, trying to run peripheral_uart sample connecting nrf5340 to a module via uart. The program seems working when only works with nrf5340 based on...
Dear Nordic Support Team,
I wanted to configure the nRF52840 dongle as radio co-processor. For that I wanted to build and flash the Thread: Co-processor sample in nRF52840...
Good day
I intend to use a power saving mode to turn on a device for a set amount of time. During this, the device would still need to receive commands over mqtt. Is this...
Dear SRs
We are evaluating your NB-IoT solution by means of Thingy91 reference board. The NB-IoT service is working with iBASIS card, the question is: can we change the...
I've created the samples for Socket Echo Client https://developer.nordicsemi.com/nRF_Connect_SDK/doc/2.0.2/zephyr/samples/net/sockets/echo_client/README.html#sockets-echo...
HI , I am having difficulty in interfacing the flash with my DK board
1) The spi flash sample is getting stuck at flash erase function without any error responses
2) I...
I see this case mentions constant tone extension. Currently, only nRF52833, nRF52820 and nRF52811 can do this.
https://devzone.nordicsemi.com/f/nordic-q-a/59948/nrf52-selection...
Hi,
We're working on a development project using nRF52832, SDK 15.2 and s132_nrf52_6.1.0_softdevice. I'm trying to use the radio test example from the SDK to certify the...
Hi all,
I have a board based on an nRF52832. At the moment I program it through the nRF52 Dev-kit (with the debug out connector) as my board doesn't have any debugger...
I'm a complete idiot when it comes to Nordic, this is literally my first time experience with any Nordic chips. I have a little experience programming ESP32-s3 chips, and...
Im working on a windows 11 Pro (OS Build 22000.1219) with a NRF52 development kit which has a NRF52832 chip set. The board is PCA10040 3.0.0. The device does not communicate...
Hi,
I run the sample zephyr/samples/bluetooth/periodic_adv on 5340, if the controller selected software-base ( CONFIG_BT_LL_SW_SPLIT ), the sample work well; if BT controller...
Hello,
Currently we're working on improving our DALI driver on the nRF52832 chip, because we've experienced issues with transmitting DALI bits with the correct timing. The...
