I want to change data bytes in the advertisement packet. In ACI_DEVICE_STANDBY I put: lib_aci_open_adv_pipe(1);
In ACI_EVT_CMD_RSP: I get feedback that command 1B (I assume...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Hello! I'm using sdk8 and s110. I want my peripheral device to send data to the central. I doing following steps:
1. initialize service:
void services_init(void)
{...
I am glad that I have successfully used the library from www.libstock.com/.../nordic-semi-nrf24l01-example in a pair of PIC18F45k50 devices. One is acting as a Tx and another...
Hello.
I have had a search but can not find anything so sorry if this has been covered before.
Our company has developed a consumer product using the nRF51822-QFAA-R7...
We are starting a new wearable device design which will be worn by the user on the chest. We are looking forward to use NRF5340/NRF52840 based modules. The final design is...
hello together,
I would like to use this chip nRF9160-SIAA-B1A-R now only as LTE modem. But the modem should be controlled by two external MCU. Please see figure.
...
Hi support team,
Our purpose is to provide the modules to our customers. We have developped the hardware module based on nrf52832. Now we want to test the BLE mesh functionalities...
I used VDD channel to detected battery voltage, and the P0.5(AIN3) connect to a LED, But I found that after initialize SAADC, P0.5 cannot control output.
Hi Nordic
I have some questions regarding switch to Application on custom address.
The memory layout in flash is like this:
0x00000000 - MBR 0x00000000 - softdevice...
Hi, I am new to the nRF Connect extension in VS Code and I am having trouble including dealy.h header file to utilize a DelayMs() function. I found the delay.h in the sdk...
I am advertising some data, my hardware is minimum and there are no external interrupts.
1. How do I wake up after entering power save mode with __WFE(); ?
2. I also want...
Hi ,
I want to use above PMIC for Gotek tracker. But I have below questions:
1. Due to the IO limitation, can I use static high or low to configure the chip with VOUTB...
Hello,
We are working on a product that has UART and SPI integrated. We initialise the UART and the SPI at the beginning of the code and everything works fine.
However...
I am using the nRF52840 and the pair of Nordic BLE UART Demo projects ble_app_uart_c_pca10056_s140 and ble_app_uart_pca10056_s140
Please can you tell me how to change the...
Hello all, Currently I am developing a code for a BLE central device that is supposed to receive data from a weight scale (peer). The peer has a service with a custom 128...
Dear friends,
My 52840 DK flashed a serial example(nrf5_SDK_for_Mesh_v5.0.0_src\examples\serial) as a provisioner.
Now, I want to factory reset my provisoner by PyACI...
Good day,
We are trying to interface TCAN4550 to nRF52840 over SPI, and found that sometimes TCAN throws SPI error (underflow of read/write). Looking further, we found that...
Hello all,
I am developing a BLE application with the Softdevices, the peer management module, and with MITM protection.
I've set a bonding static passkey as shown here...
I run a custom multilink BLE service server on nRF9160 DK.
After about 20 minutes of repeated connecting, data exchange and disconnecting from 4 (only four) BLE devices...
