But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hi,
we are using nrf52 DK and our custom mobile application. We are trying to collect 15000 sensor samples and finally we are trying to send array to mobile app via BLE...
I suspect there is a bug in the https_client sample. sdk-nrf/samples/net/https_client/src/main.c
The certificate seems to always be provisioned and
mismatch = modem_key_mgmt_cmp...
I have tried to use the power profiler and I got the notification that my firmware had to be updated. I clicked proceed and the device started updating.
When the update...
Hello,
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am using NUS to work with...
My Android app builds and runs fine under Android 13.
But on Android 14 when I try to use the DFU library (ver. 2.5.0) I get the following run-time error: One of RECEIVER_EXPORTED...
I have two nrf5340 audio DKs running bidirectional audio over Bluetooth. Software is modified Audio example from SDK 2.7.0. I am trying to run external i2s in the unicast...
Hello,
I am currently programming using SPIM+Timer+PPI(via nRF Connect SDK v.2.6.1), but due to my lack of understanding, handling handlers is challenging. Therefore, I...
Hello! I am using the nRF5340 dev board with an nRF7002ek wifi shield to connect to MQTT using the Zephyr MQTT library and MQTT 3.1.1 (the only supported version by Zephyr...
Dear Nordic Team, I am currently working with 2 Infineon IM73D122V01 PDM Mems microphones to obtain stereo data, One is configured as left and the other is configured as right...
Hi,
We have 2 projects where we are using the nPM1300.
In both cases we have peak currents.
In de documentations I thought I read some where that the current limit was...
Hello,
this is connected to the question:
For our application I need all radio on/off events. The sample "connection event trigger" sample only gives one trigger per connection...
Hi Nordic,
I am implementing a micros() in the arduino using nrfx driver.
Below is test code and I got some questions.
[Question 1]
Timer 1 and Timer 2 works...
I am currently using nrf52840, nRF5_SDK_17.1.0_ddde560, and the ble_app_multirole_lesc example file.
I have successfully removed the HRS and button Bluetooth connections...
