We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hello,
I'm trying to create a PC application to read out some Ti Sensor Tag modules. I'm using a nRF51822 USB dongle and the Master Emulator api.
The nRF dongle sees...
Hi All,
I have design my customer board but after production nothing looks to work. i can program the board through the Nordic board by using debug out. even a simple blinky...
I have a BLE code, when it runs on NORA-B106 it gives me -20dB difference on comparison to nRF5340 Nordic DK.
It was not expected such a big difference, what could be the...
I have been trying to implement the wifi scan or wifi provisioning code on a module (MS12SF1) which is a combine wifi + ble module
The setup looks like the image shown below...
Hi,
I'm developing with NCS v2.6.0 for Raytac MDBT53v-P1M module, which inhibits nRF5340. I already have my own PCB with all the required HW components.
As a sanity check...
Hi I would like to report a bug in the Devicetree visual editor.
When you add two fixed regulators and connect a separate sensor to each of them, both sensors will be represented...
I am trying to get a SST25 spi flash running, but the jedec,spi-nor driver does only partially work.
As i understand now the jedec,spi-nor driver only works with CFI compatible...
Hi, I am experiencing low power issues on a nRF52840 DK 3.0.2 board which I have not seen on another one with version 3.0.0. I do not know the root cause yet.
For my investigations...
Hi
I am powering the nRF52840 from a 3.3V DC power supply and connecting it with a IMU thats cannot go higher than 1.9V on the I2C bus
I use 1.8V.
Will the I2C coomuncation...
Hi,
I have a new NRF5340-DK and I am trying to connect it via usb on linux but do not see it in the syslog when connected. I actually do not see anything at all.
When...
Hi,
I want to implement a pwm output signal on a particular pin of the nRF52840DK working with the latest nRF Connect for VS Code. What would be the recommended way to setup...
Hi,
I tried to flash the blinky example to an nRF52840 Dongle as described here:
https://academy.nordicsemi.com/flash-instructions-for-nrf52840-dongle/
Console output...
Hi I'm trying to create a transparent CDC to NUS bridge, this is based on the nrf52840 dongle.
The Aim of this is to send binary files to our device from a PC, our device...
I wrote a code for GPIO interrupt when DRDY pin goes high to low(Data ready) interrupt should occur and call a function but it is not working Below is a code:
intDRDY =...
Trying to implement FOTA DFU over BLE. My application uses my proprietary code (instead of mcumgr) to download signed OTA firmware image to secondary slot (in my case it is...
