This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
I’m using the nRF52840DK to communicate with a module over uart. My problem is that the module has a baud rate of 921600 and as far as my understanding the nRF52840 is using...
Hi,
in my current project I need to have a wall clock time, thus I am using the date_time library. While trying to understand it I came across a few issues/questions.
...
Hello,
First let me say I'm new to Nordic tools and SDK. I have been lurking on this forum for a while and it has helped solve a lot of my issues in the past. I couldn't...
Hello
I tried to follow the instructions to install the nRF SDK Connect and I found the following issues:
There are 2 sets of instructions :
option 1 :
https://nrfconnect...
Hi! We would like to build two different sw variants from same source code and mostly the same config options, probably only needing a single "define"-difference in code....
Hi,
We have a question regarding firmware over the air update, can we update the firmware of the devices connected in Mesh network or we need to connect single device...
Hello,
to use the twi sensor library should I define for each sensor an own NRF_TWI_SENSOR_DEF?
I found not really a documentation about the usage of the twi sensor library...
Hi,
I've got a lot of BLE_GAP_EVT_TIMEOUT when my ble central trying to connect with BLE peripheral (sometimes more than six in a row).
The configuration of my system...
HI,
I have couple of questions here.
1.Is there any sample application that upgrade firmware over BLE using zephyr/NCS 2.1.0 for nRF52840
2.If so our requirement is...
We are using QSPI XIP mode to access data in external flash for our project. We are trying put QSPI peripheral in standby mode.
However, we can't uninitialized QSPI peripheral...
I want to develop a device with the following selection.
BLE module: Raytac MDBT42V (nRF52832)
nRF Connect SDK v1.2.0
Where can I check the version of SoftDevice...
Good Day!
I have a Samsung Note 10 smartphone (it supports Long Range) and I want to connect it to an nRF52840 microcontroller using BLE Long Range.
What is the approximate...
Hello
I was using the NRF52840 dev kit as J-link to develop a custom board. at first was working, i uploaded a blink code to it then i modified the libry from gpio.h to...
Hi,
We used the SLM (serial LTE modem) application in our custom board with NRF9160 configured as a slave chip and interfaced with an STM32 MCU via UART interface. The SDK...
Hi there,
Currently developing a producting using two nRF52833 boards one as peripheral and one as central:
- 125kbs coded phy (S8)
- 40 byte MTU
- using extended...
