But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
nrf9160-DK to NB-IOT service at vodafore UK
```
[00:00:00.322,479] [0m<inf> asset_tracker: Connecting to LTE network. [0m[00:00:00.329,193] [0m<inf> asset_tracker: This...
I know that we have actually some countries in Europe which don't support LTE-M, therefore we like to have a fallback.
Does there exist a fallback option to GSM or EGPRS...
Hi,
So I was having an error which caused my application to stall in the "do_stop_check" part of the nrf_drv_twi.c file, so I added a bit of code to check if I could figure...
We have a device with the following configuration:
nrf5_SDK_for_Mesh_v3.1.0
nRF5_SDK_15.2.0
s140_nrf52_6.1.0_softdevice
mesh_bootloader_gccarmemb_nrf52840_xxAA ...
Hi,
I'm trying to make a script in Python using the nRF52840 dongle, to make some BLE advertising.
I'm using:
- Python 3.7.2 (32 bit)
- pc_ble_driver_py library
...
Hi everyone,
I'm using ses IDE to debug via J-link on nRF52840 DK.
I'm debbuging CDC ACM example ( I haven't changed it ) but when I debug: ret = app_usbd_cdc_acm_write...
I am designing a PCB for the nRF52833 aQFN chip. To reduce the cost of the PCB I would like to fanout the inner row of the IC package on a single layer by using 3/3mil traces...
Hello,
I have a certificate attached, but in my personal account it gives an error when I enter the DK data.
Please tell me why the error occurs?
OS: macOS 10.13.6 ...
Hi,
I am using IM69D130 MEMS sensor with nrf52832 I just want to confirm the output of pdm sensor . please any one suggest how should i proceed . how do i code for it ?...
I am attempting to migrate my BLE project to a higher security level with bonding. Was mode 1 level 2 and am upgrading to mode 1 level 4. When I change the configuration to...
Nrf52832 chip is used, and the software package is the “nRF5_SDK_16.0.0_98a08e2” version.
According to customer feedback, Bluetooth connection is generally unstable...
Hello
I've seen several places that it is posible to build the project using jenkins, and hook Jenkins to the git repo where our nRF sourcecode resides.
Unfortunately...
