Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
my PCB board uses nRF9161 SiP. The flash chip is W25N02KVZEIR.
on the PCB board, here are the wiring to spi flash chip,
P0.26 to CS#, P0.27 to CLK, P0.28 to MOSI, P0.29...
Hi Nordic team,
I’m currently using an nRF9160 DK and trying to test LTE-M connectivity with a custom test SIM and a network emulator. However, I’m facing multiple issues...
Hello,
I am using the nRF54L15-DK development kit. The peripheral-uart example works well to stream data from the kit to a smartphone using the nRF-tools App. However...
I am trying to use the ADC on an nRF52840DK.
I have configured the two ADC channels in the overlay
I setup the channels like this
and take readings using this code...
Hi, I have faced dificulties calling zsock_poll for ZSOCK_POLLIN with multiple opened sockets, expecially when conbined TCP and UDP at the same time. My goal is it poll for...
So when I toggle the pin high, it gets set to 1.8V. I want it to be at least 2.8V. I did configure the VDD to 3.3V. The VDDIO does show 3.3V, but a pin like let say P1.11...
I have been trying to use the ` nrf\samples\bluetooth\peripheral_nfc_pairing ` sample code on the nRF Connect SDK v3.0.2 to connect to a Samsung Galaxy A16 5G phone.
The...
I bought a tiny board on Aliexpress from HolyIOT. It comes with an nRF52832 and an LIS2DH12 accelerometer. The silkscreen on the board says HOLYIOT-21011-v1.0.
This schematic...
Hello,
We are developing a board with both nrf91 and nrf54 boards. We are looking to make the nrf91 a SLM with a UART interface to support the LTE functionality of the nrf54...
Hi, I have two concerns about the functions nrf_gpiote_subscribe_set, nrf_gpiote_subscribe_clear, nrf_gpiote_publish_set, and nrf_gpiote_publish_clear. The expression
*...
Hello,
I'm trying to figure out why I get this warning that seems to block the compilation process but a bit of context first :
I'm resuming a project that was paused...
Hi,
I am trying to create a new board, following the Exercise 1 – Custom board for single-core SoC (nRF Connect SDK Intermediate), but I am getting this error:
Does...
Hi,
After I executed nrfjprog --rbp ALL , how can I unlock the chip so that I can program the board again?
Currently, the only way I can program it is by running the following...
Dear Nordic Devzone,
I have some questions regarding battery profiling procedures.
1. Is it normal for battery profiling to take longer than 8 days? As you can see in...
