But now I have a new problem that is whenever I set " PWR_UP " bit in CONFIG register then it drop the 3.3 volt vcc to 1.2 volt. I don't know why its happening. Anyway, is...
This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello,
I am trying to define a pm_static.yml file which will use the 512K ram on the nrf7002dk_nrf5340 for the TFM ram section.
I cannot compile the non-secure nrf7002dk...
Hi, I got my nrf54L15 DK, but i can't start RTT logging. I set this configs:
CONFIG_PRINTK =y
CONFIG_CONSOLE =y
CONFIG_RTT_CONSOLE =y
CONFIG_UART_CONSOLE =n
CONFIG_USE_SEGGER_RTT...
Hi,
Is there any ongoing development for a PPK3 ? If so, what is the timeline for its release ?
Some features requested in previous posts:
- Voltage measurement
-...
Hi,
Could you please clarify why there is an override of the checking rules in https://github.com/nrfconnect/sdk-zephyr/blob/ncs-v3.1.1/drivers/timer/Kconfig.nrf_rtc#L6C8...
We are developing a custom board with an ADC device that supports QSPI. Our application requires throughput speeds only available using QSPI.
All the available driver examples...
Hi,
I would like to use existing development setup (for STM32) :Visual Studio 20XX (not VS code) with VisualGDB plugin to work with the nRF9151 Development Kit.
However...
Hello, I have a project implementing the ASYNC UART API as laid out in the Nordic Development academy exercise. I had this successfully communicating with an external device...
Hi,
I run a couple test with the PPK2 on our board to measure and optimize the power consumption, but I had some weird results and I'm hopping you can help me out to understand...
Hi,
I am looking at setting up some of our team with the ability to flash our custom devices that contain various chips (nrf52, nrf53, nrf91). Assuming the SEGGER software...
Hi,
I can't program nRF52840 dongle using Programmer Tool on Linux.
Dongle is visible, can be selected and memory content read without any problems but file write attempt...
Hi nordic support:
Our product used nRF52840 and nrf5_sdk_17.1.0. It's inconvenient to connect UART port when perform DTM test to testing nRF52840's RF performance. Could...
Hi there,
I hope this message finds you well!
I’ve been developing several products using Espressif’s modules that offer both Wi-Fi and BLE on a single SoC. I wanted to...
I'm developing a custom board that uses the nRF54H20.
The Getting Started guide for the nRF54H20DK explains how to use the pre-built BICR file and program it to the chip...
Hi Team, We are facing significant range issues on iPhones and other iOS devices with our hardware. We have tested these with both Custom App ( Made in House ) as well as...
