This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi Dev team,
My question is related to the charging of the Thingy91 battery through solar panels. I have a solar panel connected to the Thingy on the points TP11 (Vbus)...
Hello, i installed nrfjprog version: 10.14.0 external, JLinkARM.dll version: 6.86f. When i download hex file use nrfjprog -f, there is no log like erase 0xxxxx. How can i...
Hello,
I am facing the following issue:
I am using the blinky sample of Zephyr to control the output of a pin. When this pin is any of the LED pins of nrf5340dk, the output...
Dear Nordic engineers
I study the AES examples.I have a question and would like to ask you.
I study the aes_ctr examples.I found that this program use two functions to...
Hello. I am trying to change the UUID value of a service and characteristic of my nRF52 to have a custom value. I have successfully done this in firmware and it has been found...
Hello everybody,
I am currently working on a project in which I need to read some data from a glucometer. Until last week it was working fine, however I stopped receiving...
Hello,
I installed nRF Connect SDK V2.0.0 using "NRF connect for Desktop"
Now I can't open nRF Connect SDK projects on segger embedded studio.
It showing only VS Code...
Hi,
I'm trying to get a better understanding what causes some unexpected current peaks while nRF9160 is in RRC-IDLE with the NB-IoT mode. I have been experimenting with...
Hi,
I have installed the nRF Connect SDK v2.0.0 with Visual Studio and can now successfully, build, flash and run the nrf9160 at_client sample application. But when I try...
Hi,
I am trying to run any of the samples, even the most basic ones as blinky, and they will not run on my nRF52840 dongle, which has a header to program directly with jlink...
Hi,
I have installed the nRF Connect SDK v2.0.0 with Visual Studio and can now successfully, build, flash and run the nrf9160 at_client sample application. But when I try...
Hi,
I have installed the nRF Connect SDK v2.0.0 with Visual Studio and can now successfully, build, flash and run the nrf9160 at_client sample application. But when I try...
Hi,
I have installed the nRF Connect SDK v2.0.0 with Visual Studio and can now successfully, build, flash and run the nrf9160 at_client sample application. But when I try...
Hi,
I am trying to run the sample code for the BME680 sensor over I2C.
I am using the sample code as is; the only modification is my overlay file to define the I2C pins...
