Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hello,
I am currently testing a custom board using the nRF5340QKAA .
Most of the connections are the same as the nRF5340 DK , but the main difference is that I built the...
I dont have Ellisys, but I already install Ellisys Bluetooth Analyzer on my PC.
I got a .btt file in this ticket , but it seems something wrong.
I want some .btt files...
I am using an nRF52840 processor within a Particle Argon IoT module. I am polling a third party BLE peripheral (Shelly relay) for status data once a minute. The data packet...
when i try to use the ddfs to calculate the distance, i can't understand the comments in the README file,
"Zero-distance calibration
*************************
The...
I have followed the guide at https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/ncs-dfu .
(using the option CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU...
After the Matter device is upgraded from version 1.1 to 1.3 via OTA, the Thread connection is functioning normally., but it fails to process chip-tool commands, and chip-tool...
I'm interested in connecting a device to a combination of RAK4631 and RAK5802 using RS485 interface.
I write the code in the Zephyr environment and I cant seem to make it...
"I'm trying to perform DFU using MCUBOOT over Bluetooth. The device enters DFU mode and connects successfully, but when I start the firmware download, I get an error:
Starting...
Hello Nordic Team,
I am currently implementing low-level SPI communication using SDK v2.7.0 and nRF 5340dk . Could you please let me know the name of the IRQ handler for...
I have received my NRF52840 DK V3 and i open NRF connect for Desktop and run "Quick Start", it have detect the board but when i try the hello world program test it is not...
Hi Nordic team, We have a project that uses nRF5340 &NCS 2.7.0, and we encountered net core crashing issue each time when ble is connected by central device and 5340 app core...
Description:
Hello,
I am trying to build my project nrf_dm_testing using NCS 2.9.0 , but I am encountering a CMake configuration error. The error message is as follows...
I am using 9160 as slave which communicates with nrf5340(master) over UART. with flow control disabled everything works but as soon as I enable the hardware flow control then...
Hello,
I have a few questions regarding the nPM1300 current measurements:
As far as I understand, there are two ways to trigger a current measurement:
By writing...
